Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis x600-24Ts-POE manual System Fault LED is Blinking

Models: x600-24Ts-POE

1 110

Download 110 pages 37.26 Kb

Page 96

Chapter 5: Troubleshooting

System Fault LED is Blinking

A blinking FAULT LED indicates that the switch is updating the active boot configuration file or a new version of the operating system software is in the process of being downloaded to the switch. The LED stops blinking after the switch has completed updating the boot configuration file or downloading the operating system software.

96

Image 96

Allied Telesis x600-24Ts-POE manual System Fault LED is Blinking

Contents

Installation Guide x600 Series Layer 3 Gigabit Ethernet Switchesx600-24Ts x600-24Ts/XP x600-48Ts x600-48Ts/XP x600-24Ts-POE Copyright 2009 Allied Telesis, Inc Electrical Safety and Emissions Standards Translated Safety Statements Contents 10/100/1000Contents x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide 17-pin Connector Pinouts21-pin D-combo Port and Connector Pinouts RJ-45 Style Serial Terminal Port PinoutsContents List of Figures Figures List of Tables Tables Preface ˆ “Safety Symbols Used in this Document” on pageˆ “Where to Find Web-based Guides” on page ˆ “Product Documentation” on pageˆ Virtual Chassis Stacking VCS How To Note ˆ AT-StackXG Stacking Module Installation GuideProduct Documentation ˆ AlliedWare Plus Operating System Software Reference GuideStarting a Management Session x600 Layer 3 Gigabit Ethernet Switch Installation GuideSafety Symbols Used in this Document SymbolMeaning DescriptionWhere to Find Web-based Guides x600 Layer 3 Gigabit Ethernet Switch Installation GuideOnline Support Email and Telephone Support Warranty Returning Management Software UpdatesContacting Allied Telesis Products Sales or Corporate InformationOverview ChapterIntroduction Switch Descriptions Figure 1. x600-24Ts Switchx600-24Ts/XP Switch Figure 2. x600-24Ts/XP SwitchAC Power Connector100-240VAC~ RPS INPUT x600-48Ts/XP Switch Figure 4. x600-48Ts/XP SwitchFigure 5. x600-24Ts-POE Switch TransceiverConsole Connector Type Speed Duplex Mode Maximum Distance 10/100/1000Base-T PortsCable Type Auto-MDI/ MDI-X Port Pinouts SFP Transceiver Slots XFP Transceiver Slots Combo Ports ModelsPorts and Slots SD Card Slot AlliedWare Plus Operating System Software Reference GuidePort LEDs 10/100/1000 Base-T LEDsFunction StateDescription LINK/ACT LEDs 2. The PoE LED is only present on the x600-24Ts-POE switchFunction StateXFP Transceiver Slot LEDs FunctionState DescriptionSystem STATUS LEDs FAULT MASTER RPS RESET PWRState DescriptionSTACK LEDs State DescriptionSecure Digital SD LED FunctionState DescriptionTerminal Port Power Over Ethernet Maximum Power ClassMaximum Power Usage6. A legacy device is a node that was manufactured before the IEEE 802.3af standard was completed and may not be compliant. If the device does not conform to the standard, a cross-over cable may be required to insure that the correct DC polarity is supplied to the device Redundant Power Supplies AT-LBM Loop Back Module VCS Stacking Module AC Power Connector Chapter 1 Overview Virtual Chassis Stacking ChapterFeatures of VCStacking The Physical Stack VCStackTM IntroductionVCS Stacking Modules, Cables, and Connections VCStack Recovery States Ring ConfigurationResiliency Link Stack Resiliency Link Event on Master Node Reaction onReaction on Stack With Resiliency LinkResiliency Link Configurations via Switch Ports Figure 25. Resiliency link connecting to switch ports over theFigure 26. Resiliency link connecting to switch ports over the ResiliencyLink VLAN using a network hubResilient Stacked Topology Stack Formation The Role of the Stack MasterSelecting the Stack Master Common Stack Configuration Stack Management VLANStack Member Identification DescriptionStack Member Failure and Recovery Running QoS within a VCS stackManagement IP Addresses Description ContinuedVCS Failure Recovery Fallback ActionRe-elect New Stack Master Recombining Separated StacksStack Maintenance Repairing a Broken StubAdding a Stack Member Replacing a Stack MemberChapter 2 Virtual Chassis Stacking Installing the Hardware ˆ “Reviewing Safety Precautions” on pageˆ “Unpacking a Switch” on page ˆ “Installing the Power Cord Retaining Clip” on pageReviewing Safety Precautions All Countries Install product in accordance with local and National Electrical Codes. E8 Caution The unit does not contain field serviceable components. Please return damaged units for servicing Unpacking a Switch Installing the Power Cord Retaining Clip Installing the Switches in an Equipment Rack Figure 32. Mounting the Switch in a Rack Resetting the Switch VC Stacking Module Installation Installing the AT-StackXG Module Figure 36. Installing the AT-StackXG Stacking Module 5.3.1 Software Reference Figure 38. Removing the Plastic ProtectorChapter 3 Installing the Hardware Cabling the Network Ports x600 switch. The chapter contains the following sectionsˆ “Twisted Pair and Fiber Optic Specifications” on page ˆ “Installing SFP/XFP Transceivers” on pageTwisted Pair and Fiber Optic Specifications Twisted Pair Cable SpecificationsMaximum SpeedSFP/XFP Transceiver Specifications x600 Layer 3 Gigabit Ethernet Switch Installation GuideInstalling SFP/XFP Transceivers Installing an SFP TransceiverPage x600-4 Installing an XFP Transceiver 5. Repeat this procedure to install a second XFP transceiver or go to “Cabling the 10/100/1000Base-T and Fiber Optic Ports” on page Cabling the 10/100/1000Base-T and Fiber Optic Ports Powering on a Switch Starting a Local Management Session 3. Configure the terminal or terminal emulation program as follows ˆ Baud rate Default is 9600 bps Range is 9600 to 115200 bpsˆ Data bits ˆ Parity None ˆ Stop bits ˆ Flow control None Chapter 4 Cabling the Network PortsWarranty Registration x600 Layer 3 Gigabit Ethernet Switch Installation GuideChapter 4 Cabling the Network Ports Troubleshooting ChapterPower LED is Off Twisted Pair Port Link LED is Off SFP or XFP LED is Off Chapter 5 TroubleshootingTransceiver is Installed but the Status is “Not Present” System Fault LED is Blinking System Fault LED is Steadily On Cannot Establish a Local Out-of-Band Management Session Switch Functions Intermittently Issues with Virtual Stacking Chassis Configuration Chapter 5 TroubleshootingTechnical Specifications Physical SpecificationsEnvironmental Specifications Appendix AAppendix A Technical Specifications Maximum Operating Altitude3,048 m 10,000 ft Maximum Nonoperating AltitudePower Specifications CertificationsSignal RJ-45 Twisted Pair Port PinoutsSignal Pinout PairAT-RPS3104 17-pin Connector Pinouts RJ-45 Style Serial Terminal Port PinoutsSignal Definition AT-RPS3204 21-pin D-combo Port and Connector Pinouts DefinitionDefinition Appendix A Technical Specifications