Chapter 1

 

 

 

 

Setting Up the CoreModule 800

 

 

 

 

 

 

 

 

 

 

f) For LAN Boot, go to PXE Boot

 

 

• Enter PXE BIOS by pressing Ctrl + S, when you see the

 

Agent BIOS Setup after rebooting

 

following prompt appear on screen:

 

 

 

 

 

 

 

Initializing Intel (R) Boot Agent FE v4.x.xx

 

 

 

 

 

 

 

PXE v2.0 Build 084 (WfM 2.0)

 

 

 

 

 

 

 

Press Ctrl + S to enter the setup Menu..

 

 

 

 

 

 

 

• Make the necessary changes in the PXE BIOS Setup

 

 

 

 

 

 

 

before saving changes. Refer to Appendix C of the

 

 

 

 

 

 

 

CoreModule 800 Reference Manual for more information.

 

20) Install the desired

 

• Use the LAN Boot feature to load the boot (OS) image onto the hard

 

 

Operating System (OS)

 

disk drive, or other media. (See Note below) Or

 

 

 

 

• Locate the desired Operating System (OS) diskette(s) or CD-ROM and

 

 

 

 

 

follow the manufacturer’s instructions for installing the OS and the

 

 

 

 

 

necessary drivers.

 

 

 

 

 

For Windows Operating Systems, most of the necessary drivers are

 

 

 

 

 

found on the manufacturer’s installation CD-ROM.

 

 

 

 

 

For non-Windows Operating Systems, some or all of the necessary

 

 

 

 

 

drivers may be found on the manufacturer’s diskette(s) or CD-ROM.

 

 

 

 

• If you require drivers that are not available on the OS manufacturer’s

 

 

 

 

 

diskette(s) or CD-ROM, refer to Installing Software, Drivers, and

 

 

 

 

 

Utilities in Chapter 2 and the software subdirectory on the

 

 

 

 

 

CoreModule 800 Doc & SW CD-ROM for the files and instructions.

 

 

 

 

 

 

 

 

NOTE

The CoreModule 800 ships from the factory configured only for CRT

 

 

 

 

 

support. Ampro provides LCD/TFT support for flat panels with specific

 

 

 

 

 

resolutions. Refer to the CoreModule 800 Reference Manual, the

 

 

 

 

 

Release Notes, and Virtual Technician at http://ampro.custhelp.com for

 

 

 

 

 

instructions and additional information when customizing the BIOS to a

 

 

 

 

 

particular flat panel.

 

 

 

 

 

 

 

 

 

 

NOTE

LAN Boot Feature – The LAN Boot process puts the Ethernet connection at the

 

 

 

 

top of the boot order, but it requires more than just selecting the correct BIOS

 

 

 

 

Setup options. You will also need a PXE server with its tools and utilities,

 

 

 

 

which Ampro does not provide. For the PXE BIOS settings and more

 

 

 

 

information refer to Appendix C of the CoreModule 800 Reference Manual.

 

 

 

 

 

 

 

 

 

 

 

See Figures 1-1, 1-2, and 1-8 for the CoreModule 800 jumper locations. For the I/O Board jumper settings refer to Table B-1 and Figures 1-7 and B-1 for the I/O Board jumper location.

Table 1-1. CoreModule 800 Jumper Settings

Jumper #

Installed

Removed/Enabled

JP1 – CMOS Normal/Clear

Clear (1-2)

Normal (Removed) Default

 

 

 

JP2 – Serial 2

Enable Termination (1-2)

Disable Termination (Removed)

RS-485 Termination

 

Default

JP3 – Serial 1

Enable Termination (1-2)

Disable Termination (Removed)

RS-485 Termination

 

Default

JP4 – LVDS Flat Panel

Enable +3.3V (pins 1-2)

Enable +5V (pins 2-3)

Voltage Select

(Default)

 

Notes: Jumpers (or shunts) use 2 mm spacing. A jumper that is removed may be placed on one of the jumper pins for safe keeping.

10

QuickStart Guide

CoreModule 800

Page 14
Image 14
Ampro Corporation PCI-104 quick start Jumper # Installed Removed/Enabled, Default