Manuals / AMX / Musical Instruments & Equipment / Drums

AMX NXM-MHS, NXC-M/ME/MPE ICSNet RJ-45 Connections/Wiring, Preparing/connecting captive wires

Models: NXC-M/ME/MPE

1 48

Download 48 pages 38.08 Kb

Page 24

Preparing/connecting captive wires

Installation and Wiring

6.Inside the Master Card slot on the NXF or NXI, find the 6-pin control cable connector.

7.Plug the connector from the NXF or NXI into the 6-pin terminal on the Master Card. This connector is keyed to ensure correct orientation.

8.Once the control cable is connected, gently slide the card in until you feel the rear edge of the card snap into place.

9.Re-apply power and other connections as necessary.

Preparing/connecting captive wires

1.Strip 0.25 inch of wire insulation off all wires.

2.Insert each wire into the appropriate opening on the connector according to the wiring diagrams and connector types described in this section. Do not tighten the screws excessively; doing so may strip the threads and damage the connector.

ICSNet RJ-45 Connections/Wiring

The following table shows the pinouts, signals, and pairing information to use for ICSNet RJ-45 connections. The ICSNet connections provide power and data to ICSNet devices. Each port provides up to 500 mA of current.

ICSNet RJ-45 Pinouts/Signals

Pin	Signal	Connections			Pairing

1	TX +	1 ---------	1	1	--------- 2

2	TX -	2 ---------	2

3	Mic -	3 ---------	3	3	--------- 6

4	GND	4 ---------	4

5	12 VDC	5 ---------	5	4	--------- 5

6	Mic +	6 ---------	6

7	RX +	7 ---------	7	7	--------- 8

8	RX -	8 ---------	8

RJ-45 plug

RJ-45 plug

	18	NetLinx Master Cards and Modules

Image 24

AMX NXM-MHS ICSNet RJ-45 Connections/Wiring, Preparing/connecting captive wires, ICSNet RJ-45 Pinouts/Signals

Contents

NetLinx Master Cards and Modules instruction manualNXM-MHS, NXC-M/ME/MPE NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Table of Contents Installation and WiringProduct Information - NetLinx Modules NXC-M Master CardProgramming NetLinx SecurityProgram Port Commands NetLinx Security FeaturesDefault Security Configuration Setup SecurityTable of Contents Main Security MenuTable of Contents NetLinx Master Cards and ModulesProduct Information - NetLinx Modules NXM-MHS NXM ModulesNXM-MHS specifications NXM-MHS SpecificationsNXM-MHS Specifications Cont Program Port DIP switch - baud rate settingsBaud Rate Settings Program Port DIP switch - Program Run Disable PRD modePRD Mode Settings Setting the Program Port DIP SwitchProgram Port Connections/Wiring DB-9 Program Port, Pinouts, and Signals5-Pin Program Port Pinouts and Signals DB-9 Program port front panelModes and front panel LED blink patterns Modes and LED Blink PatternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs AXLinkRear panel LEDs Ethernet ME and MPE only Product Information - NetLinx ModulesSpecifications NXC-M Master CardNXC-M Master Card Specifications NXC-M Master CardInstalling an optional NCP-E Ethernet Card Rear panel components3. Mount the NCP-E to the NXC-M, as shown in FIG NXC-M Master Card NetLinx Master Cards and ModulesNXC-ME Master-Ethernet Card SpecificationsNXC-ME Specifications NXC-ME Master-Ethernet CardEthernet Ports used by the ME Ethernet Ports used by the MERear panel components NXC-ME Master-Ethernet CardNXC-MPE Master Port Expander Card SpecificationsNXC-MPE Specifications NXC-MPE Master Port Expander CardSPE Port Connection/Wiring Ethernet 10/100 LEDs Ethernet 10/100 connectorICSNet connectors/LEDs ICSHub In/Out connectors/LEDs Rear panel componentsSPE Connector Pinouts and Signals SPE Cable pinout informationNXC-MPE Master Port Expander Card NetLinx Master Cards and ModulesInstallation and Wiring Mounting the Modules Into an Equipment RackMounting the Master Cards in an NXF CardFrame or NXI ICSNet RJ-45 Connections/Wiring Preparing/connecting captive wiresICSNet RJ-45 Pinouts/Signals ICSHub RJ-45 Connections/Wiring Ethernet 10/100 Base-T RJ-45 Connections/WiringISCHub Pinouts and Signals Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries Program Port Commands ProgrammingPC COM Port Communication Settings Program Port CommandsProgram Port Commands Cont Program Port Commands Cont SET TIMEESC Pass Codes Notes on specific Telnet/Terminal clientsESC Pass Codes Windows client programsNetLinx Security Features NetLinx SecuritySecurity Terms Used in This Document NetLinx Security FeaturesPassword Access RightsUser Name Group NameInitial Setup via Telnet or Terminal connection Accessing the Security configuration optionsGetting connected If NetLinx master security is not enabled, you will see the following Security Options Menu 2 Display system security options for NetLinx master3 Add user 4 Edit User Edit User MenuAccess Rights Menu Access Rights MenuEdit User Menu Access Rights Menu Cont 5 Delete user6 Show the list of authorized users 7 Add GroupEdit Group Menu Add directory association Edit Group menu Delete directory associationNetLinx Security NetLinx Master Cards and ModulesEdit Group menu Change Access Rights Edit Group menu Display Access RightsEdit Group menu List directory associations 8 Edit Group11 Set Telnet Timeout in seconds 12 Display Telnet Timeout in seconds9 Delete Group 10 Show List of Authorized GroupsMain Security Menu CommandMain Security Menu NetLinx SecurityDefault Security Configuration Main Security Menu ContCommand Security Help menuSecurity Help Menu Options NetLinx SecurityLogging Into a Session Security Help Menu Options ContLogout Setup SecurityHelp Security Programming NetLinx Master Cards and Modulesto alter specifications Panja IncAMX logo AMX reserves