Manuals / AMX / Musical Instruments & Equipment / Drums

AMX NXC-M/ME/MPE, NXM-MHS instruction manual Mount the NCP-E to the NXC-M, as shown in FIG

Models: NXC-M/ME/MPE

1 48

Download 48 pages 38.08 Kb

Page 15

Image 15

3.Mount the NCP-E to the NXC-M, as shown in FIG. 7.

NXC-M Master Card

FIG. 6 Installing the new rear plate

3.Mount the NCP-E to the NXC-M, as shown in FIG. 7.

a.Lower the rear edge (with the Ethernet connector and LEDs) of the NCP-E first.

b.Align the connector with the opening in the rear plate.

c.Lower the other end of the NCP-E, mating the connectors on both cards.

NCP-E Ethernet Port Card

Ethernet connector housing

Port Card connector

FIG. 7 Installing the NCP-E Ethernet Card

4.Tighten the four screws (included) to secure the Ethernet port card to the NXC-M.

NetLinx Master Cards and Modules	9

Page 15

Image 15

AMX NXC-M/ME/MPE, NXM-MHS instruction manual Mount the NCP-E to the NXC-M, as shown in FIG

Contents

NetLinx Central Controllers and Cards NetLinx Master Cards and Modulesinstruction manual NXM-MHS, NXC-M/ME/MPEAMX Limited Warranty and Disclaimer NXC-M Master Card Table of ContentsInstallation and Wiring Product Information - NetLinx ModulesNetLinx Security Features ProgrammingNetLinx Security Program Port CommandsMain Security Menu Default Security ConfigurationSetup Security Table of ContentsNetLinx Master Cards and Modules Table of ContentsNXM-MHS Specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS specificationsProgram Port DIP switch - baud rate settings NXM-MHS Specifications ContSetting the Program Port DIP Switch Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode PRD Mode SettingsDB-9 Program port front panel Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals 5-Pin Program Port Pinouts and SignalsRear panel LEDs AXLink Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs ICSNet/ICSHubProduct Information - NetLinx Modules Rear panel LEDs Ethernet ME and MPE onlyNXC-M Master Card SpecificationsNXC-M Master Card NXC-M Master Card SpecificationsRear panel components Installing an optional NCP-E Ethernet Card3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-M Master CardNXC-ME Master-Ethernet Card NXC-ME Master-Ethernet CardSpecifications NXC-ME SpecificationsNXC-ME Master-Ethernet Card Ethernet Ports used by the MEEthernet Ports used by the ME Rear panel componentsNXC-MPE Master Port Expander Card NXC-MPE Master Port Expander CardSpecifications NXC-MPE SpecificationsRear panel components SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector ICSNet connectors/LEDs ICSHub In/Out connectors/LEDsSPE Cable pinout information SPE Connector Pinouts and SignalsNetLinx Master Cards and Modules NXC-MPE Master Port Expander CardInstallation and Wiring Mounting the Modules Into an Equipment RackMounting the Master Cards in an NXF CardFrame or NXI ICSNet RJ-45 Connections/Wiring Preparing/connecting captive wiresICSNet RJ-45 Pinouts/Signals Ethernet RJ-45 Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring ISCHub Pinouts and SignalsReplacing the Lithium Batteries Program Port Commands Program Port CommandsProgramming PC COM Port Communication SettingsProgram Port Commands Cont SET TIME Program Port Commands ContWindows client programs ESC Pass CodesNotes on specific Telnet/Terminal clients ESC Pass CodesNetLinx Security Features NetLinx Security FeaturesNetLinx Security Security Terms Used in This DocumentGroup Name PasswordAccess Rights User NameInitial Setup via Telnet or Terminal connection Accessing the Security configuration optionsGetting connected If NetLinx master security is not enabled, you will see the following Security Options Menu 2 Display system security options for NetLinx master3 Add user Edit User Menu 4 Edit UserAccess Rights Menu Access Rights MenuEdit User Menu 7 Add Group Access Rights Menu Cont5 Delete user 6 Show the list of authorized usersNetLinx Master Cards and Modules Edit Group Menu Add directory associationEdit Group menu Delete directory association NetLinx Security8 Edit Group Edit Group menu Change Access RightsEdit Group menu Display Access Rights Edit Group menu List directory associations10 Show List of Authorized Groups 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 9 Delete GroupNetLinx Security Main Security MenuCommand Main Security MenuMain Security Menu Cont Default Security ConfigurationNetLinx Security CommandSecurity Help menu Security Help Menu OptionsSecurity Help Menu Options Cont Logging Into a SessionLogout Setup SecurityHelp Security NetLinx Master Cards and Modules ProgrammingAMX reserves to alter specificationsPanja Inc AMX logo