Manuals / AMX / Musical Instruments & Equipment / Drums

AMX NXM-MHS, NXC-M/ME/MPE instruction manual SPE Port Connection/Wiring, Rear panel components

Models: NXC-M/ME/MPE

1 48

Download 48 pages 38.08 Kb

Page 20

Ethernet 10/100 LEDs Ethernet 10/100 connector

NXC-MPE Master Port Expander Card

Rear panel components

FIG. 9 shows the rear panel components NXC-MPE Master Port Expander Card.

NXC-MPE

Master-Ethernet

12VDC

AXlink

PWR	EXPANSION OUT

ETHERNET

10/100

SPEED FD

RTS CTS TX RX GND

Ethernet 10/100 LEDs Ethernet 10/100 connector

ICSNet connectors/LEDs ICSHub In/Out connectors/LEDs

IN

OUT

ICSNetICSHub

PROGRAM port connector Expansion port connector (RJ-11) 12 VDC power supply connector

FIG. 9 NXC-MPE Card (shown mounted in a NXS-MHS Module - rear view)

SPE Port Connection/Wiring

Use an RJ-11 cable (6" max. length) to connect the NXC-MPE to an AXB-SPE Slave Port Expander.

The SPE OUT port on the rear panel of the NXC-MPE connects to the EXPANSION IN port on the rear panel of the AXB-SPE (FIG. 10).

EXPANSION IN port (RJ-11)

FIG. 10 AXB-SPE (rear panel)

You can daisy chain multiple AXB-SPE's by connecting the EXPANSION OUT on the primary AXB-SPE to the EXPANSION IN port on the secondary, as shown in FIG. 11. The connecting RJ- 11 cable should not exceed 6 inches in length. Repeat this process to connect up to nine AXB- SPE's.

	14	NetLinx Master Cards and Modules

Image 20

AMX NXM-MHS SPE Port Connection/Wiring, Rear panel components, Ethernet 10/100 LEDs Ethernet 10/100 connector

Contents

NetLinx Master Cards and Modules instruction manualNXM-MHS, NXC-M/ME/MPE NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Table of Contents Installation and WiringProduct Information - NetLinx Modules NXC-M Master CardProgramming NetLinx SecurityProgram Port Commands NetLinx Security FeaturesDefault Security Configuration Setup SecurityTable of Contents Main Security MenuTable of Contents NetLinx Master Cards and ModulesProduct Information - NetLinx Modules NXM-MHS NXM ModulesNXM-MHS specifications NXM-MHS SpecificationsNXM-MHS Specifications Cont Program Port DIP switch - baud rate settingsBaud Rate Settings Program Port DIP switch - Program Run Disable PRD modePRD Mode Settings Setting the Program Port DIP SwitchProgram Port Connections/Wiring DB-9 Program Port, Pinouts, and Signals5-Pin Program Port Pinouts and Signals DB-9 Program port front panelModes and front panel LED blink patterns Modes and LED Blink PatternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs AXLinkRear panel LEDs Ethernet ME and MPE only Product Information - NetLinx ModulesSpecifications NXC-M Master CardNXC-M Master Card Specifications NXC-M Master CardInstalling an optional NCP-E Ethernet Card Rear panel components3. Mount the NCP-E to the NXC-M, as shown in FIG NXC-M Master Card NetLinx Master Cards and ModulesNXC-ME Master-Ethernet Card SpecificationsNXC-ME Specifications NXC-ME Master-Ethernet CardEthernet Ports used by the ME Ethernet Ports used by the MERear panel components NXC-ME Master-Ethernet CardNXC-MPE Master Port Expander Card SpecificationsNXC-MPE Specifications NXC-MPE Master Port Expander CardSPE Port Connection/Wiring Ethernet 10/100 LEDs Ethernet 10/100 connectorICSNet connectors/LEDs ICSHub In/Out connectors/LEDs Rear panel componentsSPE Connector Pinouts and Signals SPE Cable pinout informationNXC-MPE Master Port Expander Card NetLinx Master Cards and ModulesMounting the Master Cards in an NXF CardFrame or NXI Installation and WiringMounting the Modules Into an Equipment Rack ICSNet RJ-45 Pinouts/Signals ICSNet RJ-45 Connections/WiringPreparing/connecting captive wires ICSHub RJ-45 Connections/Wiring Ethernet 10/100 Base-T RJ-45 Connections/WiringISCHub Pinouts and Signals Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries Program Port Commands ProgrammingPC COM Port Communication Settings Program Port CommandsProgram Port Commands Cont Program Port Commands Cont SET TIMEESC Pass Codes Notes on specific Telnet/Terminal clientsESC Pass Codes Windows client programsNetLinx Security Features NetLinx SecuritySecurity Terms Used in This Document NetLinx Security FeaturesPassword Access RightsUser Name Group NameGetting connected Initial Setup via Telnet or Terminal connectionAccessing the Security configuration options If NetLinx master security is not enabled, you will see the following 3 Add user Security Options Menu2 Display system security options for NetLinx master 4 Edit User Edit User MenuEdit User Menu Access Rights MenuAccess Rights Menu Access Rights Menu Cont 5 Delete user6 Show the list of authorized users 7 Add GroupEdit Group Menu Add directory association Edit Group menu Delete directory associationNetLinx Security NetLinx Master Cards and ModulesEdit Group menu Change Access Rights Edit Group menu Display Access RightsEdit Group menu List directory associations 8 Edit Group11 Set Telnet Timeout in seconds 12 Display Telnet Timeout in seconds9 Delete Group 10 Show List of Authorized GroupsMain Security Menu CommandMain Security Menu NetLinx SecurityDefault Security Configuration Main Security Menu ContCommand Security Help menuSecurity Help Menu Options NetLinx SecurityLogging Into a Session Security Help Menu Options ContHelp Security LogoutSetup Security Programming NetLinx Master Cards and Modulesto alter specifications Panja IncAMX logo AMX reserves