NetLinx Security
Security Help menu
Type help at the prompt in the Telnet session to display the following help topics:
| Security Help Menu Options |
| |
|
|
| |
| Command | Description | |
|
|
| |
| (Extended diag messages are OFF) | ||
|
|
| <D:P:S>: Device:Port:System. If omitted, assumes master. |
|
|
| |
| ? or Help | Displays this list. | |
|
|
|
|
| DATE |
| Displays the current date. |
|
|
| |
| DEVICE HOLDOFF ONOFF | Sets the master to holdoff devices (i.e. does not allow them to report | |
|
|
| ONLINE) unitl the NetLinx program has completed executing the |
|
|
| DEFINE_START section. |
|
|
| If set to ON, any messages to devices in DEFINE_START will be lost, |
|
|
| however, this prevents incoming messages being lost in the master |
|
|
| upon startup. When DEVICE_HOLDOFF is ON, you must use ONLINE |
|
|
| events to trigger device startup SEND_COMMANDs. |
|
|
| By default, DEVICE HOLDOFF is OFF to maintain compatibility with |
|
|
| Axcess systems where fdevices are initialized in DEFINE_START. |
|
|
| |
| DEVICE STATUS <D:P:S> | Provides information about the specified device. | |
|
|
| |
| DNS LIST <D:P:S> | Displays the DNS configuration of a device. | |
|
|
| |
| DISK FREE | Displays the amount of free space on the disk. | |
|
|
| |
| GET DEVICE HOLDOFF | Displays the state of the device holdoff setting in the master | |
|
|
| |
| GET IP <D:P:S> | Displays the IP configuration of a device. | |
|
|
| |
| HELP SECURITY | Displays security related commands. | |
|
|
| |
| IP STATUS | Provides information about NetLinx IP Connections. | |
|
|
|
|
| MEM |
| Shows size of the largest block of available memory. |
|
|
| |
| MSG ONOFF | Enables/Disables extended diagnostic messages. | |
|
|
|
|
| OFF | [D:P:S or NAME,CHAN] | Turns off the specified channel. |
|
|
|
|
| ON | [D:P:S or NAME,CHAN] | Turns on the specified channel. |
|
|
| |
| PASS [D:P:S or NAME] | Puts the Session in pass mode to the specified device. | |
|
|
| • Mode is exited by ++ ESC ESC. |
|
|
| • Display Format is set by ++ ESC n |
|
|
| If n is A, format = ASCII |
|
|
| If n is D, format = Decimal |
|
|
| If n is H, format = Hex |
|
|
| |
| PING [ADDRESS] | Pings an address (IP or URL). | |
|
|
| Specify |
|
|
| |
| PROGRAM INFO | Displays a list of program modules loaded. | |
|
|
| |
| PULSE [D:P:S or NAME,CHAN] | Pulses the specified channel. | |
|
|
| |
| REBOOT <D:P:S> | Reboots the device. | |
|
|
| |
| RELEASE DHCP | Releases the current DHCP lease. | |
|
|
| |
| ROUTE MODE DIRECTNORMAL | Set the | |
|
|
| |
| SEND_COMMAND D:P:S or | Sends the specified command to the device.The Command uses | |
| NAME,COMMAND | NetLinx string syntax. | |
|
|
| • Ex: send_command 1:1:1,"'This is a test',13,10" |
|
|
| • Ex: send_command RS232_1,"'This is a test',13,10" |
|
|
| |
| SEND_STRING D:P:S or | Sends the specified string to the device. | |
| NAME,STRING |
| |
|
|
| |
(Cont.) | SET DATE | Set the current date. | |
|
|
| |
| 38 | NetLinx Master Cards and Modules |
|
|
|
