Replacing the Lithium Batteries | AMX NXM-MHS, NXC-M/ME/MPE instruction

Replacing the Lithium Batteries

Installation and Wiring

Replacing the Lithium Batteries

The Master Cards are equipped with two lithium batteries that have a life of approximately 5 years to protect their memory. When DC power is on, the batteries are not used. When replacing the batteries, remove one at a time to avoid losing the program in memory.

Battery (Li-Mv, 3V)

socket

FIG. 14 Lithium battery and socket

1.Discharge the static electricity from your body by touching a metal grounded object.

2.Unplug the connectors from the Controller or Module.

!NetLinx Integrated Controller (NXI): Remove the rear panel from the NXI. Then, disconnect the NXI control cable and remove the Master Card.

!NetLinx Module (NXS-MHS): Remove the rear panel from the Module. Then, remove the Master Card.

3.Carefully slide one battery out of its socket, and insert the new battery.

4.Plug the 2-pin PWR (green) connector to reapply power. Wait approximately 1 minute. Then, remove the PWR connector again.

5.Carefully slide the other battery out of its socket and insert the new battery.

6.Replace the Master Card (re-connect the NXI control cable to the Master Card if replacing in an NXI); replace the rear panel and secure with the mounting screws.

7.Reconnect all control, communication, and power cables.

	20	NetLinx Master Cards and Modules

Image 26

AMX NXM-MHS, NXC-M/ME/MPE instruction manual Replacing the Lithium Batteries

Contents

NXM-MHS, NXC-M/ME/MPE NetLinx Master Cards and Modulesinstruction manual NetLinx Central Controllers and Cards AMX Limited Warranty and Disclaimer Product Information - NetLinx Modules Table of ContentsInstallation and Wiring NXC-M Master Card Program Port Commands ProgrammingNetLinx Security NetLinx Security Features Main Security Menu Default Security ConfigurationSetup Security Logging Into a Session Table of Contents NXM-MHS specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS Specifications NXM-MHS Specifications Cont Program Port DIP switch - baud rate settings PRD Mode Settings Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode Setting the Program Port DIP Switch 5-Pin Program Port Pinouts and Signals Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals DB-9 Program port front panel Rear panel LEDs ICSNet/ICSHub Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs AXLink Rear panel LEDs Ethernet ME and MPE only NXC-M Master Card Specifications SpecificationsNXC-M Master Card NXC-M Master Card Installing an optional NCP-E Ethernet Card Rear panel components 3. Mount the NCP-E to the NXC-M, as shown in FIG NXC-M Master Card NXC-ME Master-Ethernet Card NXC-ME Master-Ethernet CardNXC-ME Specifications Port Type Ethernet Ports used by the MEEthernet Ports used by the ME Standard Port # NXC-MPE Master Port Expander Card NXC-MPE Master Port Expander CardNXC-MPE Specifications ICSNet connectors/LEDs ICSHub In/Out connectors/LEDs SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear view SPE Connector Pinouts and Signals SPE Cable pinout information NXC-MPE Master Port Expander Card Mounting the Master Cards in an NXF CardFrame or NXI Installation and WiringMounting the Modules Into an Equipment Rack ICSNet RJ-45 Pinouts/Signals ICSNet RJ-45 Connections/WiringPreparing/connecting captive wires ISCHub Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring Ethernet RJ-45 Pinouts and Signals Replacing the Lithium Batteries PC COM Port Communication Settings Program Port CommandsProgramming Program Port Commands Program Port Commands Cont SET TIME ESC Pass Codes ESC Pass CodesNotes on specific Telnet/Terminal clients Windows client programs Security Terms Used in This Document NetLinx Security FeaturesNetLinx Security NetLinx Security Features User Name PasswordAccess Rights Group Name Getting connected Initial Setup via Telnet or Terminal connectionAccessing the Security configuration options If NetLinx master security is not enabled, you will see the following 3 Add user Security Options Menu2 Display system security options for NetLinx master 4 Edit User Edit User Menu Edit User Menu Access Rights MenuAccess Rights Menu 6 Show the list of authorized users Access Rights Menu Cont5 Delete user 7 Add Group Edit Group Menu Add directory association Edit Group menu Delete directory association Edit Group menu List directory associations Edit Group menu Change Access RightsEdit Group menu Display Access Rights 8 Edit Group 9 Delete Group 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 10 Show List of Authorized Groups Main Security Menu Main Security Menu Default Security Configuration Main Security Menu Cont Security Help menu Security Help Menu Options Logging Into a Session Security Help Menu Options Cont Help Security LogoutSetup Security Programming AMX logo to alter specificationsPanja Inc AMX reserves