Manuals / AMX / Musical Instruments & Equipment / Drums

AMX NXC-M/ME/MPE, NXM-MHS SPE Cable pinout information, SPE Connector Pinouts and Signals

Models: NXC-M/ME/MPE

1 48

Download 48 pages 38.08 Kb

Page 21

Image 21

NXC-MPE Master Port Expander Card

To SPE OUT connector on rear of NXC-MPE

EXPANSION

1rst AXB-SPE (rear panel)

RJ-11 (6" max)

2nd AXB-SPE (rear panel)

OUT

FIG. 11 Daisy chaining two or more AXB-SPE's off of an NXC-MPE

SPE Cable pinout information

The following table gives pinout information for the RJ-11 SPE connector. AMX supplies the RJ- 11 cable with the AXB-SPE.

The EXPANSION connectors (on the AXB-SPE) use pins 2, 3, 4 and 5. Pin 2 is Ground; the others are all pin-to-pin connections.

SPE Connector Pinouts and Signals

Pin Signal

1no connect

2GND

3TX

4TX enable

5RX

6no connect

NetLinx Master Cards and Modules	15

Page 21

Image 21

AMX NXC-M/ME/MPE, NXM-MHS instruction manual SPE Cable pinout information, SPE Connector Pinouts and Signals

Contents

instruction manual NetLinx Master Cards and ModulesNXM-MHS, NXC-M/ME/MPE NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Installation and Wiring Table of ContentsProduct Information - NetLinx Modules NXC-M Master CardNetLinx Security ProgrammingProgram Port Commands NetLinx Security FeaturesSetup Security Default Security ConfigurationTable of Contents Main Security MenuNetLinx Master Cards and Modules Table of ContentsNXM-MHS NXM Modules Product Information - NetLinx ModulesNXM-MHS specifications NXM-MHS SpecificationsProgram Port DIP switch - baud rate settings NXM-MHS Specifications ContProgram Port DIP switch - Program Run Disable PRD mode Baud Rate SettingsPRD Mode Settings Setting the Program Port DIP SwitchDB-9 Program Port, Pinouts, and Signals Program Port Connections/Wiring5-Pin Program Port Pinouts and Signals DB-9 Program port front panelModes and LED Blink Patterns Modes and front panel LED blink patternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs AXLinkProduct Information - NetLinx Modules Rear panel LEDs Ethernet ME and MPE onlyNXC-M Master Card SpecificationsNXC-M Master Card Specifications NXC-M Master CardRear panel components Installing an optional NCP-E Ethernet Card3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-M Master CardSpecifications NXC-ME Master-Ethernet CardNXC-ME Specifications NXC-ME Master-Ethernet CardEthernet Ports used by the ME Ethernet Ports used by the MERear panel components NXC-ME Master-Ethernet CardSpecifications NXC-MPE Master Port Expander CardNXC-MPE Specifications NXC-MPE Master Port Expander CardEthernet 10/100 LEDs Ethernet 10/100 connector SPE Port Connection/WiringICSNet connectors/LEDs ICSHub In/Out connectors/LEDs Rear panel componentsSPE Cable pinout information SPE Connector Pinouts and SignalsNetLinx Master Cards and Modules NXC-MPE Master Port Expander CardInstallation and Wiring Mounting the Modules Into an Equipment RackMounting the Master Cards in an NXF CardFrame or NXI ICSNet RJ-45 Connections/Wiring Preparing/connecting captive wiresICSNet RJ-45 Pinouts/Signals Ethernet 10/100 Base-T RJ-45 Connections/Wiring ICSHub RJ-45 Connections/WiringISCHub Pinouts and Signals Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries Programming Program Port CommandsPC COM Port Communication Settings Program Port CommandsProgram Port Commands Cont SET TIME Program Port Commands ContNotes on specific Telnet/Terminal clients ESC Pass CodesESC Pass Codes Windows client programsNetLinx Security NetLinx Security FeaturesSecurity Terms Used in This Document NetLinx Security FeaturesAccess Rights PasswordUser Name Group NameInitial Setup via Telnet or Terminal connection Accessing the Security configuration optionsGetting connected If NetLinx master security is not enabled, you will see the following Security Options Menu 2 Display system security options for NetLinx master3 Add user Edit User Menu 4 Edit UserAccess Rights Menu Access Rights MenuEdit User Menu 5 Delete user Access Rights Menu Cont6 Show the list of authorized users 7 Add GroupEdit Group menu Delete directory association Edit Group Menu Add directory associationNetLinx Security NetLinx Master Cards and ModulesEdit Group menu Display Access Rights Edit Group menu Change Access RightsEdit Group menu List directory associations 8 Edit Group12 Display Telnet Timeout in seconds 11 Set Telnet Timeout in seconds9 Delete Group 10 Show List of Authorized GroupsCommand Main Security MenuMain Security Menu NetLinx SecurityMain Security Menu Cont Default Security ConfigurationSecurity Help menu CommandSecurity Help Menu Options NetLinx SecuritySecurity Help Menu Options Cont Logging Into a SessionLogout Setup SecurityHelp Security NetLinx Master Cards and Modules ProgrammingPanja Inc to alter specificationsAMX logo AMX reserves