NXC-M Master Card, Specifications | AMX NXC-M/ME/MPE, NXM-MHS

NXC-M Master Card

NXC-M Master Card

NXC-M Master Card

Specifications

NXC-M Master Card Specifications

Power Requirements	260 mA @ 12 VDC

Memory	• Disk on chip (Non-volatile): 8 MB (upgradeable to 32 MB)
	• SDRAM (Volatile): 16 MB
	• NVS (Non-volatile): 1 MB

Front Panel Components:
Connector	Program port - DB-9 (male) connector for system programming and diagnos-
	tics
LED indicators	• Status - Green LED shows AXlink/NetLink data activity.
	• Output - Red LED shows data output activity.
	• Input - Yellow LED shows data input activity.

Rear Panel Components
LED indicators	• AXlink - Green LED blinks to show AXlink data activity.
	• ICSNet - Green LEDs that light when sending/receiving data.
	• ICSHub IN/OUT - Yellow LEDs that light when sending/ receiving data.
Connectors	• PWR - 2-pin (male) green captive-wire connector for 12 VDC power.
	• AXlink - Black 4-pin (male) captive-wire connector that provides data and
	power to external control devices.
	Power rating = 6 A max; actual load depends on connected power supply.
	• PROGRAM port - 5-pin (male) gray connector for system programming and
	diagnostics.
	• ICSNet - Two RJ-45 connectors that provide power and data to external
	ICSNet devices.
	Power rating = 500 mA.
	• ICSHub IN/OUT - Two RJ-45 connectors that provide data to other Hubs
	connected to the Master Card.

Enclosure	Metal with black matte finish.

Front Faceplate	Plastic gray with translucent viewing window.

Dimensions (HWD):
Card(s)	0.5" x 4.8" x 8.5" (127 mm x 121.9 mm x 215.9 mm)
Module	1.5" x 5.0" x 8.8" (45 mm x 127 mm x 224 mm)

Weight:
Card only	11.2 oz (317.51 g)
With module	12.8 oz (362.87 g)

Optional accessories	• 12 VDC power supply (PSN 6.5, PSN 2.8)
	• AC-RK Accessory Rack Kit (Module)

NetLinx Master Cards and Modules	7

Image 13

AMX NXC-M/ME/MPE NXC-M Master Card Specifications, Rear Panel Components, NetLinx Master Cards and Modules

Contents

instruction manual NetLinx Master Cards and ModulesNXM-MHS, NXC-M/ME/MPE NetLinx Central Controllers and Cards AMX Limited Warranty and Disclaimer Installation and Wiring Table of ContentsProduct Information - NetLinx Modules NXC-M Master Card NetLinx Security ProgrammingProgram Port Commands NetLinx Security Features Setup Security Default Security ConfigurationMain Security Menu Logging Into a Session NetLinx Master Cards and Modules NXM-MHS NXM Modules Product Information - NetLinx ModulesNXM-MHS specifications NXM-MHS Specifications Program Port DIP switch - baud rate settings NXM-MHS Specifications Cont Program Port DIP switch - Program Run Disable PRD mode Baud Rate SettingsPRD Mode Settings Setting the Program Port DIP Switch DB-9 Program Port, Pinouts, and Signals Program Port Connections/Wiring5-Pin Program Port Pinouts and Signals DB-9 Program port front panel Modes and LED Blink Patterns Modes and front panel LED blink patternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs AXLink Rear panel LEDs Ethernet ME and MPE only NXC-M Master Card SpecificationsNXC-M Master Card Specifications NXC-M Master Card Rear panel components Installing an optional NCP-E Ethernet Card 3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-ME Specifications NXC-ME Master-Ethernet CardNXC-ME Master-Ethernet Card Ethernet Ports used by the ME Ethernet Ports used by the MEPort Type Standard Port # NXC-MPE Specifications NXC-MPE Master Port Expander CardNXC-MPE Master Port Expander Card Ethernet 10/100 LEDs Ethernet 10/100 connector SPE Port Connection/WiringICSNet connectors/LEDs ICSHub In/Out connectors/LEDs FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear view SPE Cable pinout information SPE Connector Pinouts and Signals NetLinx Master Cards and Modules Mounting the Modules Into an Equipment Rack Installation and WiringMounting the Master Cards in an NXF CardFrame or NXI Preparing/connecting captive wires ICSNet RJ-45 Connections/WiringICSNet RJ-45 Pinouts/Signals Ethernet 10/100 Base-T RJ-45 Connections/Wiring ICSHub RJ-45 Connections/WiringISCHub Pinouts and Signals Ethernet RJ-45 Pinouts and Signals Replacing the Lithium Batteries Programming Program Port CommandsPC COM Port Communication Settings Program Port Commands Program Port Commands Cont SET TIME Notes on specific Telnet/Terminal clients ESC Pass CodesESC Pass Codes Windows client programs NetLinx Security NetLinx Security FeaturesSecurity Terms Used in This Document NetLinx Security Features Access Rights PasswordUser Name Group Name Accessing the Security configuration options Initial Setup via Telnet or Terminal connectionGetting connected If NetLinx master security is not enabled, you will see the following 2 Display system security options for NetLinx master Security Options Menu3 Add user Edit User Menu 4 Edit User Access Rights Menu Access Rights MenuEdit User Menu 5 Delete user Access Rights Menu Cont6 Show the list of authorized users 7 Add Group Edit Group menu Delete directory association Edit Group Menu Add directory association Edit Group menu Display Access Rights Edit Group menu Change Access RightsEdit Group menu List directory associations 8 Edit Group 12 Display Telnet Timeout in seconds 11 Set Telnet Timeout in seconds9 Delete Group 10 Show List of Authorized Groups Main Security Menu Main Security Menu Main Security Menu Cont Default Security Configuration Security Help Menu Options Security Help menu Security Help Menu Options Cont Logging Into a Session Setup Security LogoutHelp Security NetLinx Master Cards and Modules Panja Inc to alter specificationsAMX logo AMX reserves