Manuals / AMX / Musical Instruments & Equipment / Drums

AMX NXC-M/ME/MPE ICSHub RJ-45 Connections/Wiring, Ethernet 10/100 Base-T RJ-45 Connections/Wiring

Models: NXC-M/ME/MPE

1 48

Download 48 pages 38.08 Kb

Page 25

ICSHub RJ-45 Connections/Wiring

Installation and Wiring

ICSHub RJ-45 Connections/Wiring

The two ICSHub RJ-45 connectors on the rear of the Master Card provide data to other Hubs connected to a downstream system. Hubs allow you to connect multiple NetLinx Hubs together in a daisy-chain configuration. Connect the OUT port to the IN port on the second or downstream NetLinx hub. The following table describes the pinout/signal information.

ISCHub Pinouts and Signals

	IN Port		OUT Port

Pin	Signal	Pin	Signal

1	TX -	1	RX +

2	TX +	2	RX -

7	RX -	7	TX +

8	RX +	8	TX -

RJ-45 plug

RJ-45 plug

!Use CAT5 cables for all ICSHub connections.

!Do not connect the last hub in a daisy-chain configuration to the first hub.

Ethernet 10/100 Base-T RJ-45 Connections/Wiring

The following table describes the RJ-45 pinouts, signals and pairing for the Ethernet 10/100 Base-T RJ-45 connector and cable.

Ethernet RJ-45 Pinouts and Signals

Pin	Signals	Connections		Pairing

1	TX +	1 ---------	1	1 ---------	2

2	TX -	2 ---------	2

3	RX +	3 ---------	3	3 ---------	6

4	no connection	4 ---------	4

5	no connection	5 ---------	5

6	RX -	6 ---------	6

7	no connection	7 ---------	7

8	no connection	8 ---------	8

RJ-45 plug

RJ-45 plug

NetLinx Master Cards and Modules	19

Image 25

AMX NXC-M/ME/MPE, NXM-MHS ICSHub RJ-45 Connections/Wiring, Ethernet 10/100 Base-T RJ-45 Connections/Wiring

Contents

instruction manual NetLinx Master Cards and ModulesNXM-MHS, NXC-M/ME/MPE NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Installation and Wiring Table of ContentsProduct Information - NetLinx Modules NXC-M Master CardNetLinx Security ProgrammingProgram Port Commands NetLinx Security FeaturesSetup Security Default Security ConfigurationTable of Contents Main Security MenuNetLinx Master Cards and Modules Table of ContentsNXM-MHS NXM Modules Product Information - NetLinx ModulesNXM-MHS specifications NXM-MHS SpecificationsProgram Port DIP switch - baud rate settings NXM-MHS Specifications ContProgram Port DIP switch - Program Run Disable PRD mode Baud Rate SettingsPRD Mode Settings Setting the Program Port DIP SwitchDB-9 Program Port, Pinouts, and Signals Program Port Connections/Wiring5-Pin Program Port Pinouts and Signals DB-9 Program port front panelModes and LED Blink Patterns Modes and front panel LED blink patternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs AXLinkProduct Information - NetLinx Modules Rear panel LEDs Ethernet ME and MPE onlyNXC-M Master Card SpecificationsNXC-M Master Card Specifications NXC-M Master CardRear panel components Installing an optional NCP-E Ethernet Card3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-M Master CardSpecifications NXC-ME Master-Ethernet CardNXC-ME Specifications NXC-ME Master-Ethernet CardEthernet Ports used by the ME Ethernet Ports used by the MERear panel components NXC-ME Master-Ethernet CardSpecifications NXC-MPE Master Port Expander CardNXC-MPE Specifications NXC-MPE Master Port Expander CardEthernet 10/100 LEDs Ethernet 10/100 connector SPE Port Connection/WiringICSNet connectors/LEDs ICSHub In/Out connectors/LEDs Rear panel componentsSPE Cable pinout information SPE Connector Pinouts and SignalsNetLinx Master Cards and Modules NXC-MPE Master Port Expander CardMounting the Modules Into an Equipment Rack Installation and WiringMounting the Master Cards in an NXF CardFrame or NXI Preparing/connecting captive wires ICSNet RJ-45 Connections/WiringICSNet RJ-45 Pinouts/Signals Ethernet 10/100 Base-T RJ-45 Connections/Wiring ICSHub RJ-45 Connections/WiringISCHub Pinouts and Signals Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries Programming Program Port CommandsPC COM Port Communication Settings Program Port CommandsProgram Port Commands Cont SET TIME Program Port Commands ContNotes on specific Telnet/Terminal clients ESC Pass CodesESC Pass Codes Windows client programsNetLinx Security NetLinx Security FeaturesSecurity Terms Used in This Document NetLinx Security FeaturesAccess Rights PasswordUser Name Group NameAccessing the Security configuration options Initial Setup via Telnet or Terminal connectionGetting connected If NetLinx master security is not enabled, you will see the following 2 Display system security options for NetLinx master Security Options Menu3 Add user Edit User Menu 4 Edit UserAccess Rights Menu Access Rights MenuEdit User Menu 5 Delete user Access Rights Menu Cont6 Show the list of authorized users 7 Add GroupEdit Group menu Delete directory association Edit Group Menu Add directory associationNetLinx Security NetLinx Master Cards and ModulesEdit Group menu Display Access Rights Edit Group menu Change Access RightsEdit Group menu List directory associations 8 Edit Group12 Display Telnet Timeout in seconds 11 Set Telnet Timeout in seconds9 Delete Group 10 Show List of Authorized GroupsCommand Main Security MenuMain Security Menu NetLinx SecurityMain Security Menu Cont Default Security ConfigurationSecurity Help menu CommandSecurity Help Menu Options NetLinx SecuritySecurity Help Menu Options Cont Logging Into a SessionSetup Security LogoutHelp Security NetLinx Master Cards and Modules ProgrammingPanja Inc to alter specificationsAMX logo AMX reserves