Programming, Program Port Commands | AMX NXC-M/ME/MPE, NXM-MHS

Programming

Programming

Programming

The NetLinx programming language allows numbers in the range 0-32,767. Device 0 refers to the Master Card, and numbers greater than 32,767 are reserved for internal use only.

The NetLinx programming language requires a Device:Port:System (D:P:S) syntax where Axcess expects only a device number. The NetLinx D:P:S triplet variable is expressed as:

DEVICE:PORT:SYSTEM

where:

•Device: 16-bit integer representing the device number (0-32,767). 0 = the Master.

• Port:	16-bit integer representing the port number (in the range 1 through the number of
	ports on the NetLinx Master.
• System:	16-bit integer representing the system number (0 = this system).

Program Port Commands

The Program port commands listed in the table below can be sent directly to the Master Card using a terminal program (i.e. Telnet). Be sure that your PC's COM port and terminal program's communication settings match those in the following table:

PC COM Port Communication Settings

Baud	38400 (default)

Parity	none

Data Bits	8

Stop Bits	1

Flow Control	none

In your terminal program, type "Help" or a "?" <Enter> to display the Program port commands listed below.

Program Port Commands

Command	Description

DATE	Displays the current date and day of the week.

DEVICE STATUS <D:P:S>	Displays a list of all active (on) channels for the specified D:P:S. Enter
	DEVICE STATUS without the D:P:S variable, the Master Card displays
	ports, channels, and version information.

DNS LIST <D:P:S>	Displays:
	• Domain suffix
	• Configured DNS IP Information

DOC FREE	Displays the total bytes of free space available on the Master Card's Disk
	on Chip.

ECHO OFF	Disables terminal character's echo (display) function.

ECHO ON	Enables terminal character's echo (display) function.

GET IP <D:P:S>	Displays the Master Card's D:P:S, Host Name, Type (DHCP or Static), IP
	Address, Subnet Mask, Gateway IP, and MAC Address.

MEM	Displays the largest free block of Master Card memory.

NetLinx Master Cards and Modules	21

Image 27

AMX NXC-M/ME/MPE, NXM-MHS instruction manual Programming, Program Port Commands, PC COM Port Communication Settings

Contents

NetLinx Central Controllers and Cards NetLinx Master Cards and Modulesinstruction manual NXM-MHS, NXC-M/ME/MPE AMX Limited Warranty and Disclaimer NXC-M Master Card Table of ContentsInstallation and Wiring Product Information - NetLinx Modules NetLinx Security Features ProgrammingNetLinx Security Program Port Commands Logging Into a Session Default Security ConfigurationSetup Security Main Security Menu NetLinx Master Cards and Modules NXM-MHS Specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS specifications Program Port DIP switch - baud rate settings NXM-MHS Specifications Cont Setting the Program Port DIP Switch Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode PRD Mode Settings DB-9 Program port front panel Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals 5-Pin Program Port Pinouts and Signals Rear panel LEDs AXLink Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs ICSNet/ICSHub Rear panel LEDs Ethernet ME and MPE only NXC-M Master Card SpecificationsNXC-M Master Card NXC-M Master Card Specifications Rear panel components Installing an optional NCP-E Ethernet Card 3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-ME Master-Ethernet Card NXC-ME SpecificationsNXC-ME Master-Ethernet Card Standard Port # Ethernet Ports used by the MEEthernet Ports used by the ME Port Type NXC-MPE Master Port Expander Card NXC-MPE SpecificationsNXC-MPE Master Port Expander Card FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear view SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector ICSNet connectors/LEDs ICSHub In/Out connectors/LEDs SPE Cable pinout information SPE Connector Pinouts and Signals NetLinx Master Cards and Modules Installation and Wiring Mounting the Modules Into an Equipment RackMounting the Master Cards in an NXF CardFrame or NXI ICSNet RJ-45 Connections/Wiring Preparing/connecting captive wiresICSNet RJ-45 Pinouts/Signals Ethernet RJ-45 Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring ISCHub Pinouts and Signals Replacing the Lithium Batteries Program Port Commands Program Port CommandsProgramming PC COM Port Communication Settings Program Port Commands Cont SET TIME Windows client programs ESC Pass CodesNotes on specific Telnet/Terminal clients ESC Pass Codes NetLinx Security Features NetLinx Security FeaturesNetLinx Security Security Terms Used in This Document Group Name PasswordAccess Rights User Name Initial Setup via Telnet or Terminal connection Accessing the Security configuration optionsGetting connected If NetLinx master security is not enabled, you will see the following Security Options Menu 2 Display system security options for NetLinx master3 Add user Edit User Menu 4 Edit User Access Rights Menu Access Rights MenuEdit User Menu 7 Add Group Access Rights Menu Cont5 Delete user 6 Show the list of authorized users Edit Group menu Delete directory association Edit Group Menu Add directory association 8 Edit Group Edit Group menu Change Access RightsEdit Group menu Display Access Rights Edit Group menu List directory associations 10 Show List of Authorized Groups 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 9 Delete Group Main Security Menu Main Security Menu Main Security Menu Cont Default Security Configuration Security Help Menu Options Security Help menu Security Help Menu Options Cont Logging Into a Session Logout Setup SecurityHelp Security NetLinx Master Cards and Modules AMX reserves to alter specificationsPanja Inc AMX logo