Redundant Switch Controller, Remote Monitoring Rmon | Avaya P550R

■If a router port for intelligent multicasting is mirrored with a piggyback port, the piggyback port is listed instead of the router port.

Redundant Switch Controller

The following problem has no workaround:

■Do not enable redundancy unless you have a redundant switch controller.

■On a P880 with an 80-series supervisor module, the redundant switch controller may not take over when the active switch controller fails.

Remote Monitoring (RMON)

The following problems have no workaround:

■30 minute RMON statistics always show utilization as 0 (Zero) on a heavily used Gigabit Ethernet port.

■Statistics for unicast frames do not work when using multilayer (ISL) tagging.

Simple Network-Management Protocol (SNMP)

	The following problems have no workaround:
	■ Cold start traps cannot be transmitted out of inband
	interfaces after you enable Spanning Tree.
	■ ipAddrTable does not display inactive interfaces (VLANs). An
	inactive interface occurs when there are no active ports on a
	VLAN.
Problem:	■ If you use the CLI to perform either of the following
	commands, the supervisor module stops responding and
	resets:
	— snmp walk aarpNetAddress
	— snmp walk cjnAtEchoSend
Workaround:	Use SNMP from a management station to access these MIB items.

610-0184-095

June 14, 2001

25

Image 25

Avaya P550R, P580, P880 manual Redundant Switch Controller, Remote Monitoring Rmon, Simple Network-Management Protocol Snmp

Contents

Overview Cajun P550R/P580/P880/P882 Switch Release Notes Software Features New Hardware and Software FeaturesHardware June 14 Queue Classification and Servicing Features Supported Product Binaries and Boot CodesType of Switch Binary File Boot File Overview Classification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series Modules Setting Up Port Mirroring Configuring Port Mirroring By Using the CLI Port Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel If you select Then Configuring Port Mirroring By Using the Web Agent Enabling Option 82 for Dhcp Changing the Status of Option 82 by Using the Web Agent Changing the Status of Option 82 by Using Snmp Changing the Status of Option 82 by Using the CLIMIB Item Cjnipv4serv.mib Enabling MAC Address Lock and Traps by Using the CLI Enabling MAC Address Lock and Traps by Using the Web AgentEnabling Traps for Unknown Source Addresses ProminetMib.txt, version Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt MIB, MIB Items, and OIDs for MAC Address Lock Corrected Problems Changed CLI CommandsEnhancements Command Line Interface CLI Known Problems and WorkaroundsATM Uplink Modules Flood Rate Limiting Desired Rate Web or CLI Setting Frames Transmitted with Cyclic Redundancy Check CRC Errors Igmp Group Membership Table Hot Swap ModulesIntelligent Multicasting Example L3 Forwarding Cache IPX Point-to-Point Protocol PPP and Telnet Option 82 for Dchp Series Modules Port Mirroring Remote Monitoring Rmon Redundant Switch ControllerSimple Network-Management Protocol Snmp P580/P882 Chassis Slot Downloading the Startup Configuration FileSupervisor Module Following error message in the CLI Switch Ports Web AFT Issues Vlan IssuesFunctional Restrictions Auto-Negotiation CajunView Checksum Error MessageCPU Synchronization Legacy CLI Hunt Groups Distance Vector Multicast Routing Protocol DvmrpLink Status Netscape Loopback TestsOversized Packets Software License Keying Redundant Controller SupportSpanning Tree Protocol STP 3Com Tagging Tftp Download Status Delay Documentation Updates and CorrectionsCajun P550R/P880/P882 Switch User Guide Web Agent Click Interfaces Technical Support Command Setting the Priority of a Port Examples Setting a Port to Ignore Tag Priority Displaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings