Enhancements, Changed CLI Commands, Corrected Problems | Avaya P880

Enhancements

The following events are now logged in the event log:

■Saving the running configuration to the startup configuration

■Creating an IP interface

■Modifying an IP interface

■Deleting an IP interface

Changed CLI Commands

■The get Fabric_mode command replaces the get Cajun_mode command.

■The set Fabric_mode command replaces the set Cajun_mode command.

Corrected Problems

The following problems have been corrected in this release:

■Pulling the base port on a hunt group no longer causes traffic to lose duplexity and broadcast to all ports within the VLAN.

■The SNMP error message no longer displays when you perform a LOADMIB operation.

■You can now create a row in the GenAppFile table in the

LOAD MIB.

■A software modification has been implemented for the LEDS on the 24-port, 10/100 Ethernet module with RJ45 connectors. The LEDs no longer illuminate when nothing is connected to them.

■The switch no longer stops learning remote MAC addresses over the ATM link when 36 or more virtual switch ports (VSPs) are configured.

■When running AppleTalk Network Assistance, the switch no longer stops forwarding layer 3 traffic.

610-0184-095

June 14, 2001

17

Image 17

Avaya P880, P580, P550R manual Enhancements, Changed CLI Commands, Corrected Problems

Contents

Overview Cajun P550R/P580/P880/P882 Switch Release Notes Hardware New Hardware and Software FeaturesSoftware Features June 14 Queue Classification and Servicing Features Supported Product Binaries and Boot CodesType of Switch Binary File Boot File Overview Classification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series Modules Setting Up Port Mirroring Configuring Port Mirroring By Using the CLI Port Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel If you select Then Configuring Port Mirroring By Using the Web Agent Enabling Option 82 for Dhcp Changing the Status of Option 82 by Using the Web Agent Changing the Status of Option 82 by Using Snmp Changing the Status of Option 82 by Using the CLIMIB Item Cjnipv4serv.mib Enabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using the Web AgentEnabling MAC Address Lock and Traps by Using the CLI ProminetMib.txt, version Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt MIB, MIB Items, and OIDs for MAC Address Lock Enhancements Changed CLI CommandsCorrected Problems Command Line Interface CLI Known Problems and WorkaroundsATM Uplink Modules Flood Rate Limiting Desired Rate Web or CLI Setting Frames Transmitted with Cyclic Redundancy Check CRC Errors Intelligent Multicasting Hot Swap ModulesIgmp Group Membership Table Example L3 Forwarding Cache IPX Point-to-Point Protocol PPP and Telnet Option 82 for Dchp Series Modules Port Mirroring Simple Network-Management Protocol Snmp Redundant Switch ControllerRemote Monitoring Rmon Supervisor Module Downloading the Startup Configuration FileP580/P882 Chassis Slot Following error message in the CLI Switch Ports Web AFT Issues Vlan IssuesFunctional Restrictions Auto-Negotiation CajunView Checksum Error MessageCPU Synchronization Legacy CLI Link Status Distance Vector Multicast Routing Protocol DvmrpHunt Groups Oversized Packets Loopback TestsNetscape Software License Keying Redundant Controller SupportSpanning Tree Protocol STP 3Com Tagging Tftp Download Status Delay Documentation Updates and CorrectionsCajun P550R/P880/P882 Switch User Guide Web Agent Click Interfaces Technical Support Command Setting the Priority of a Port Examples Setting a Port to Ignore Tag Priority Displaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings