Manuals / Brands / Computer Equipment / Switch / Avaya / Computer Equipment / Switch

Avaya P550R, P580, P880 Checksum Error Message, CajunView v3.0, CPU Synchronization , Legacy CLI

1 43

Download 43 pages, 204.58 Kb

29

610-0184-095 June 14, 2001

Workaround: Either:

■Disable auto-negotiation

■Use a patch cable that is longer that 5 meters

■Enter the following Enhanced CLI command in legacy mode:

> port set NationalPhyMode <slot>.<port> enable

The factory default for the National Phy Mode is Enable.

Checksum Error Message

Problem: The following checksum error displays after you upgrade from 4.3.x

code to v5.x code:

Bad file header compressed checksum...transfer cancelled.

Workaround: Ignore the checksum error and reboot the switch to upgrade the

software.

CajunView v3.0

CajunView v3.0 does not support 80-series hardware. CajunView

v4.0 will support 50-series hardware and 80-series hardware on

Cajun switch software code version 5.1 and later.

CPU Synchronization

Problem: If you attempt to synchronize the active supervisor and redundant

supervisor while the supervisor is being heavily used, TFTP transfers

from the active supervisor to the redundant supervisor may time out

and fail.

Workaround: Repeat the synchronization when use of the supervisor has

decreased.

Legacy CLI

Problem: The Legacy CLI setup command does not save information that you

enter.

Contents

Main Cajun P550R/P580/P880/P882 Switch Release Notes v5.2.2 Overview http://www.avayanetwork.com/ New Hardware and Software Features Hardware Software Features Page Supported Product Binaries and Boot Codes Queue Classification and Servicing Features Overview Classification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series Modules Configuring Port Mirroring By Using the CLI Setting Up Port Table 2. Port Ranges for 80-Series Port Mirroring Page Removing Port Viewing Information about Port Configuring Port Mirroring By Using the Web Agent Setting Up Port Removing Port Viewing Information about Port Mirroring Enabling Option 82 for DHCP Changing the Status of Option 82 by Using the Web Agent Changing the Status of Option 82 by Using the CLI Changing the Status of Option 82 by Using SNMP Enabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using the Web Agent Enabling MAC Address Lock and Traps by Using the CLI Enabling MAC Address Lock and Traps by Using SNMP Page Enhancements Changed CLI Commands Corrected Problems Known Problems and Workarounds ARP Problem: Workaround: ATM Uplink Modules Frames Transmitted with Cyclic Redundancy Check (CRC) Errors Problem: Workaround: Hot Swap Modules IGMP Group Membership Table Problem: Workaround: Intelligent Multicasting Workaround: IP IPX Problem: Workaround: L3 Forwarding Cache Option 82 for DCHP PCMCIA Problem: Workaround: Point-to-Point Protocol (PPP) and Telnet Port Mirroring 80-Series Modules Problem: Workaround: Problem: Redundant Switch Controller Remote Monitoring (RMON) Workaround: Simple Network-Management Protocol (SNMP) Problem: P580/P882 Chassis Slot 2 Downloading the Startup Configuration File Problem: Workaround: Supervisor Module Switch Ports Problem: Workaround: RIP Problem: Functional Restrictions Auto-Negotiation Workaround: Checksum Error Message Problem: Workaround: CajunView v3.0 CPU Synchronization Distance Vector Multicast Routing Protocol (DVMRP) IEEE 802.1Q Packets Problem: Workaround: Hunt Groups Loopback Tests Netscape 6.0 Oversized Packets PCMCIA Port Mirroring Page TFTP Download Status Delay VLAN Issues Web Agent Problem: Documentation Updates and Corrections Cajun P550R/P880/P882 Switch User Guide Technical Support Appendix A: CLI Commands for Queue Classification and Servicing Overview Setting the Priority of a Port Setting a Port to Ignore Tag Priority Displaying the Port Settings Setting a Rule in an Access Control List Page Displaying Access Control Lists Setting WFQ Overview Command 1 Command 2 Displaying the Queue Service Settings