Documentation Updates and Corrections, Web Agent | Avaya P580, P880

TFTP Download Status Delay

It takes a few seconds before the Status button on the TFTP

Download screen returns accurate information.

VLAN Issues

■Automatic VLAN creation on P880 50-series supervisor module (M5500R-SUPA) does not work if the port default VLAN is set to “discard”. The switch does not learn VLANs with this setting.

■Automatic VLAN creation on an 80-series supervisor module (M8000R-SUP) does work if the port default VLAN is set to “discard”.

■If you set a port’s VLAN trunking mode to Clear, you must set the VLAN Binding Type to Static (default).

■You may receive an error message stating that the VLAN name is already in use after you add a VLAN and refresh your browser.

Web Agent

Problem:If you click the Back button after you change a variable from the “Switch Port Config” screen, the variable will change back to the previous setting and the switch will reset. If you change a number of variables and click the Back button, the last variable will change back to the original value and the switch will reset.

Workaround: This only happens on Microsoft Internet Explorer, version 5.00.2919.6307. Use a later version of Microsoft Internet Explorer.

Documentation Updates and Corrections

The following problems were found in the Cajun P550R/P880/P882 Switch documentation for release v5.0 and will be fixed in release v6.0.

Cajun P550R/P880/P882 Switch User Guide

The following problem was found in the Cajun P550R/P880/P882

Switch User Guide for release v5.0 and will be fixed in release v6.0.

610-0184-095

June 14, 2001

33

Image 33

Avaya P580, P550R, P880 manual Documentation Updates and Corrections, Tftp Download Status Delay, Web Agent

Contents

Overview Cajun P550R/P580/P880/P882 Switch Release Notes New Hardware and Software Features Software FeaturesHardware June 14 Queue Classification and Servicing Features Supported Product Binaries and Boot CodesType of Switch Binary File Boot File Overview Classification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series Modules Setting Up Port Mirroring Configuring Port Mirroring By Using the CLI Port Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel If you select Then Configuring Port Mirroring By Using the Web Agent Enabling Option 82 for Dhcp Changing the Status of Option 82 by Using the Web Agent Changing the Status of Option 82 by Using Snmp Changing the Status of Option 82 by Using the CLIMIB Item Cjnipv4serv.mib Enabling MAC Address Lock and Traps by Using the Web Agent Enabling MAC Address Lock and Traps by Using the CLIEnabling Traps for Unknown Source Addresses ProminetMib.txt, version Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt MIB, MIB Items, and OIDs for MAC Address Lock Changed CLI Commands Corrected ProblemsEnhancements Command Line Interface CLI Known Problems and WorkaroundsATM Uplink Modules Flood Rate Limiting Desired Rate Web or CLI Setting Frames Transmitted with Cyclic Redundancy Check CRC Errors Hot Swap Modules Igmp Group Membership TableIntelligent Multicasting Example L3 Forwarding Cache IPX Point-to-Point Protocol PPP and Telnet Option 82 for Dchp Series Modules Port Mirroring Redundant Switch Controller Remote Monitoring RmonSimple Network-Management Protocol Snmp Downloading the Startup Configuration File P580/P882 Chassis SlotSupervisor Module Following error message in the CLI Switch Ports Web AFT Issues Vlan IssuesFunctional Restrictions Auto-Negotiation CajunView Checksum Error MessageCPU Synchronization Legacy CLI Distance Vector Multicast Routing Protocol Dvmrp Hunt GroupsLink Status Loopback Tests NetscapeOversized Packets Software License Keying Redundant Controller SupportSpanning Tree Protocol STP 3Com Tagging Tftp Download Status Delay Documentation Updates and CorrectionsCajun P550R/P880/P882 Switch User Guide Web Agent Click Interfaces Technical Support Command Setting the Priority of a Port Examples Setting a Port to Ignore Tag Priority Displaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings