Other I/O, RS232 serial communication, Location | Baldor iMN1921

4.6	Other I/O
4.6.1	RS232 serial communication
			Location	Serial
				Mating connector: 9-pin female D-type
			Pin	Name	Description
			1	SC	Shield connection
			2	RXD	Receive Data
			3	TXD	Transmitted Data
		1	4	(NC)	(Not connected)
	6	1	5	0V GND	Signal Ground
	6

	9	5	6	(NC)	(Not connected)
		5	7	RTS	Request To Send
			7	RTS	Request To Send
			8	CTS	Clear To Send
			9	DGND	Ground
			Description	RS232 connections on a 9-pin male D-type connector

This connector is used to connect the NextMove ST to the PC running WorkBench v5, or other controller. It is a full-duplex RS232 serial port with the following preset configuration:

H57,600 baud

H1 start bit

H8 data bits

H1 stop bit

HNo parity

HHardware handshaking lines (RS232) RTS and CTS must be connected.

The configuration can be changed using the SERIALBAUD keyword. It is stored in EEPROM and restored at power up. The port is capable of operation at up to 115,200 baud.

The port is configured as a DCE (Data Communications Equipment) unit so it is possible to operate the controller with any DCE or DTE (Data Terminal Equipment). Full duplex transmission with hardware handshaking is supported.

Only the TXD, RXD and 0V GND connections are required for communication. Pins 4 and 6 are linked on the NextMove ST.

MN1921

Input / Output 4-15

Image 29

Baldor iMN1921 installation manual Other I/O, RS232 serial communication, Location, Pin Name Description

Contents

NextMove ST Motion Controller Page Contents Operation General Information Precautions Safety Notice MN1921 Introduction NextMove ST features Receiving and inspection Units and abbreviations Phase Introduction MN1921 Location requirements You should read all the sections in Basic InstallationIntroduction Mounting the NextMove ST Package dimensions Other requirements for installation Basic Installation MN1921 Input / Output Connector locations Operation using combined drive and logic supply Power connections Connecting separate drive and logic supplies Operation using separate drive and logic supplies Stepper axes 0-2 drive outputs Connecting a 4-wire motorStepper outputs Connecting a 6-wire motor Connecting a 8-wire motor, parallel windings Connecting a 8-wire motor Stepper output pin header J3, and output circuit shown Stepper axes 0-3 logic outputs Analog inputs Analog I/O Analog output Analog output Digital inputs Digital I/O Using a digital input as a Stop input Using a digital input as a Limit or Home inputUsing a digital input as an Error input Auxiliary Encoder inputs Auxstep IN, Auxdir IN, Auxz Digital output DOUT0 shown Digital outputs Driveenableoutput keyword Error outputGlobalerroroutput keyword Jumper settings RS232 serial communication Other I/OLocation Pin Name Description RS232 serial port connections 2 50-pin edge connector Typical can network connections Can communication CANopen and Baldor can JP1 This will connect an internal terminating resistor Host PC Connection summary minimum system wiring Input / Output MN1921 Installing WorkBench Connecting the NextMove ST to the PCStarting the NextMove ST Preliminary checks Power on checks Help file WorkBench Starting WorkBench MN1921 Operation Selecting a scale Configuring an axis Click Apply Testing the output Stepper axis testing Digital input configuration Digital input/output configuration Digital output configuration Saving setup information Loading saved information SupportMe feature Problem diagnosis Status display NextMove ST indicators Surface mount LEDs D3, D4 and D16 Motor control Symptom CheckCommunication Output power Value Input power Input impedance 120 Input ADC resolution Bits Common mode voltage rangeEquivalent resolution ±10V input Output current max Update interval Immediate Unit Value Maximum output frequency KHz 200 Output voltage Stepper axis 0-2 drive outputsOutput current maximum, per axis Unit Value Output type Can interface Unit Value SignalEnvironmental Channels Protocols CANopen Index Index MN1921 Comment Comments Comments MN1921 Page LT0184A00