Selecting an input source, Using the OSD menu | BenQ SH960 instruction

Selecting an input source

The projector can be connected to multiple equipment at the same time. When the projector is first turned on, it will attempt to reconnect with the input source which was in use when the projector was last shut down.

To select the video source:

•Using the remote control or projector

Press one of the Source keys on the remote control, or press SOURCE repeatedly until your desired signal is selected.

•Using the OSD menu

1.Press MENU/EXIT and then press / until the System Setup menu is highlighted.

2.Press to highlight Input Source and press ENTER. The source selection bar is displayed.

3.Press / repeatedly until your desired signal is selected and press

ENTER.

Once detected, the selected source information will be displayed on the screen for seconds. If there are multiple pieces of equipment connected to the projector, you can go back to the source selection bar again to search for other signals.

•If you want the projector to automatically search for the signals, select On in the System Setup > Quick Auto Search menu.

•If you want to use the PIP function, see "Displaying more than one image source simultaneously" on page 41 for details.

System Setup

Language	English
Splash Screen	BenQ
Projector Position	Floor Front
Auto Power Off	Disable
Sleep Timer	Disable
Background Color	Blue
Menu Settings
Input Source	ENTER
Quick Auto Search	On
Closed Caption
Standby Monitor Out	Off
S-Video	EXIT Back

	HDMI	NOTE: When
		automatically
	Video	searching for a valid
	S-Video	input source, the
		projector cycles
	Component 1	through the
	Component 2	available signals
	Component 2	following the
		following the
	PC	sequence from top
		to bottom as the
		source selection bar
		shows.

English

Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector's HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

1.Press MENU/EXIT and then press / until the Display menu is highlighted.

2.Press to highlight Color Space Conversion and press / to select a suitable color space.

This function is only available when the HDMI input port is in use.

Using the projector

21

Image 21

BenQ SH960 user manual Selecting an input source, Using the OSD menu, Changing Color Space

Contents

Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contents Remote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Rear viewUnder view Control panel Controls and functions Remote control MuteOperating the Laser pointer Floor Front Choosing a locationCeiling Front Floor Rear Obtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensions Highest Installation for a 43 ratio screenLens Height H To use the lens shift lever Shifting the projection lens Preparations Connecting Hdmi devicesTerminal appearance Reference Picture quality Component Connecting S-Video or video devices Connecting component-video devices Connecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Preparations Turning the projector on Using the OSD menu Selecting an input sourceChanging Color Space Using a security cable lock Using the menusUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settings Setting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MENU/EXIT Changing the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Ii. See step iv below for further operation Correcting picture distortionTwo parallel sides No parallel sides Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To select a picture mode that suits your need Resetting the picture mode Setting the User 1/User 2 modeTo reset the picture mode to the preset factory values Renaming user modes Fine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image clarity Selecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperature To adjust and store the settings Setting Film ModeTo leave and save the settings, press MENU/EXIT Color Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 display Hiding the image Utilizing FAQ functionFreezing the image Press Enter Setting the lamp mode Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring Tone Controlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environment Controlling the projector remotely through a web browser Ii To switch input source, click on your desired signalAuto Source Menu item Category Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude Mode To display the PIP window Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinations Turning the projector off POWER/ON II again On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options Display System Setup Information Setup Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projector Setting Auto Power Off Setting Lamp Mode as Dual-ReliableLamp information Getting to know the lamp hour Timing of replacing the lamp Replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Indicators Power eventsLight Status & Description Problem Cause Remedy Troubleshooting Optical SpecificationsElectrical Terminals Dimensions Ceiling mount installationMm x 354.7 mm x 167 mm W x D x H Format Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputs Warranty CopyrightDisclaimer