Setup, Information | BenQ SH960 manual

Main menu		Sub-menu		Options
			Lamp Mode	Dual-Brightest/Dual-Reliable/Single-
			Lamp Mode	Alternative
				Alternative
	Lamp Settings		Reset Lamp Timer 1

			Reset Lamp Timer 2
			Reset Lamp Timer 2

			Equivalent Lamp Hour #1

			Equivalent Lamp Hour #2

				Auto
	HDMI Settings		HDMI Format
	HDMI Settings		HDMI Format	PC Signal

				Video Signal

	Baud Rate			2400/4800/9600/14400/19200/38400/57600/
	Baud Rate			115200
				115200
	High Altitude Mode			On/Off

			Mute	On/Off
	Audio Settings
	Audio Settings		Volume
Advanced
Advanced			Power On/Off Ring Tone	On/Off
Setup
Setup	Password		Password	On/Off
	Password		Change Password	(inputs current password)
			Change Password	(inputs current password)

			Control By	RS232/RJ45

			DHCP	On/Off

			Projector IP Address

	Lan Control Settings		Subnet Mask

			Default Gateway
			Default Gateway

			DNS Server

			AMX Device Discovery	On/Off

			Apply	Enter

	Reset All Settings

	Direct Power On			On/Off

	Signal Power On			On/Off

	Expert Mode			(inputs current password)

	FAQ-Image and Installation

		FAQ-Features and Service

		Source

	Information	Picture Mode

		Resolution
		Resolution

		Lamp Mode

		Equivalent Lamp Hour #1

		Equivalent Lamp Hour #2

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

English

Using the projector

45

Image 45

BenQ SH960 user manual Setup, Information

Contents

Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contents Remote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Rear viewUnder view Control panel Controls and functions Remote control MuteOperating the Laser pointer Floor Front Choosing a locationCeiling Front Floor Rear Obtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensions Highest Installation for a 43 ratio screenLens Height H To use the lens shift lever Shifting the projection lens Preparations Connecting Hdmi devicesTerminal appearance Reference Picture quality Component Connecting S-Video or video devices Connecting component-video devices Connecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Preparations Turning the projector on Using the OSD menu Selecting an input sourceChanging Color Space Using a security cable lock Using the menusUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settings Setting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MENU/EXIT Changing the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Ii. See step iv below for further operation Correcting picture distortionTwo parallel sides No parallel sides Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To select a picture mode that suits your need Resetting the picture mode Setting the User 1/User 2 modeTo reset the picture mode to the preset factory values Renaming user modes Fine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image clarity Selecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperature To adjust and store the settings Setting Film ModeTo leave and save the settings, press MENU/EXIT Color Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 display Hiding the image Utilizing FAQ functionFreezing the image Press Enter Setting the lamp mode Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring Tone Controlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environment Controlling the projector remotely through a web browser Ii To switch input source, click on your desired signalAuto Source Menu item Category Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude Mode To display the PIP window Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinations Turning the projector off POWER/ON II again On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options Display System Setup Information Setup Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projector Setting Auto Power Off Setting Lamp Mode as Dual-ReliableLamp information Getting to know the lamp hour Timing of replacing the lamp Replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Indicators Power eventsLight Status & Description Problem Cause Remedy Troubleshooting Optical SpecificationsElectrical Terminals Dimensions Ceiling mount installationMm x 354.7 mm x 167 mm W x D x H Format Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputs Warranty CopyrightDisclaimer