Specifications, Optical, Electrical, Terminals | BenQ SH960 guide

Specifications

All specifications are subject to change without notice.

Optical

Projection system			Single-chip DLP™ system.
DMD chip			0.65" DLP (1920 x 1080)
Lens			F = 2.48 to 2.81, f = 24.1 to 36.15 mm
Projection screen size			28" to 300"
Lamp			330W
		Electrical	PC: 640 x 480 to 1920 x 1200


Compatibility
			Video: NTSC, PAL, SECAM, YPbPr (480i/480p/576i/576p/720p/
			1080i/1080p), HDTV (720p/1080i/1080p)
Color Space			Typ. = 60% NTSC (Target Color Gamut = HDTV Rec. 709)
		Terminals	Analog RGB: D-Sub 15-pin (female) x 1


Input
			HDMI (V. 1.3) x 1
			Component Video (Y/CB/CR, Y/PB/PR) x 1
			Component Video (Y/CB/CR, Y/PB/PR) x 1 (shared with RGB input)
			Composite Video x 1
			S-Video x 1
			Audio in x 1
Output			12VDC (Max. 0.5 A)
			Analog RGB: D-Sub 15-pin (female) x 1
			Audio out x 1
			Speaker: 5W x 2
Control			Serial Connector: RS232 9 pin (male)
			Mini B type USB x 1
			IR receiver x 2
			LAN x 1
		General characteristics


Projector weight			< 11 kg (24.3 lbs)
Power			VAC 100-240V, 10 A, 50-60Hz
Power consumption			Max. 940 W; Standby < 1 W
Operating temperature			0 °C to 40 °C (without condensation)
Operating humidity			10% - 90% (without condensation)
Operating altitude			0-1499 m at 0°C-35°C
			1500-3000 m at 0°C-30°C (with High Altitude Mode on)
Storage temperature			-20°C- 60°C/-4°F to 140°F
Storage humidity			10% - 90%

English

Additional information

59

Image 59

BenQ SH960 user manual Specifications, Optical, Electrical, Terminals

Contents

Welcome Table of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Overview Shipping contents Ceiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Front and upper side viewRear view Control panel Controls and functions Operating the Laser pointer Remote controlMute Floor Rear Choosing a locationFloor Front Ceiling Front Obtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensions Height H Installation for a 43 ratio screenHighest Lens To use the lens shift lever Shifting the projection lens Component Connecting Hdmi devicesPreparations Terminal appearance Reference Picture quality Connecting S-Video or video devices Connecting component-video devices Connect the projector to a computer with a VGA cable Connecting a computerConnecting a monitor Preparations Turning the projector on Changing Color Space Using the OSD menuSelecting an input source Press MENU/EXIT twice* to leave and save the settings Using the menusUsing a security cable lock Use / to highlight the System Setup menu To leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the password Write down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password function Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image No parallel sides Correcting picture distortionIi. See step iv below for further operation Two parallel sides To select a picture mode that suits your need Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture mode Renaming user modes Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory values Fine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controls To set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant Color Color Management Setting Film ModeTo adjust and store the settings To leave and save the settings, press MENU/EXIT About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio image Press Enter Utilizing FAQ functionHiding the image Freezing the image Turning off the Power On/Off Ring Tone Adjusting the soundSetting the lamp mode Adjusting the sound level If you are in a non-DHCP environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environment Menu item Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Auto Source Category Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude Mode PIP function is effective at below source combinations Displaying more than one image source simultaneouslyTo display the PIP window Highlight PIP and press / to select On Turning the projector off POWER/ON II again Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Display System Setup Information Setup Function Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menu Information menu Storing the projector Cleaning the lensCleaning the projector case Care of the projector Getting to know the lamp hour Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Lamp information Status Message Timing of replacing the lampReplacing the lamp English Resetting the lamp timer Reset Lamp Timer? Light Status & Description IndicatorsPower events Problem Cause Remedy Troubleshooting Terminals SpecificationsOptical Electrical Mm x 354.7 mm x 167 mm W x D x H DimensionsCeiling mount installation KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC input Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Hdmi Hdcp input Disclaimer WarrantyCopyright