Turning the projector off, POWER/ON II again | BenQ SH960 specification

English

Turning the projector off

To turn the projector off, press POWER ( II ) on the projector or ON II on the remote control and a warning message appears. Press

POWER/ON ( II ) again.

•The Power indicator light flashes orange and the fans run for about two minutes to cool the lamp. The projector will not respond to any commands until the cooling process is complete.

•Then, the Power indicator light is a steady orange once the cooling process has finished and fans stop.

•If the projector will not be used for an extended period, unplug the power cable from the power outlet.

•To protect the lamp, the projector will not respond to any commands during the cooling process.

• Actual lamp life may vary due to different environmental conditions and usage.

•If you attempt to re-start the projector shortly after shutdown, the

fans may run for a few minutes to cool down. Press II Power/ON again to start the projector after the fans stop and the Power indicator light turns orange.

42 Using the projector

Image 42

BenQ SH960 user manual Turning the projector off, POWER/ON II again

Contents

Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents Overview Remote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Rear viewUnder view Controls and functions Control panel Remote control MuteOperating the Laser pointer Ceiling Front Choosing a locationFloor Front Floor Rear Obtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screen Lens Installation for a 43 ratio screenHighest Height H Shifting the projection lens To use the lens shift lever Terminal appearance Reference Picture quality Connecting Hdmi devicesPreparations Component Connecting component-video devices Connecting S-Video or video devices Connecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Turning the projector on Preparations Using the OSD menu Selecting an input sourceChanging Color Space Use / to highlight the System Setup menu Using the menusUsing a security cable lock Press MENU/EXIT twice* to leave and save the settings If you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MENU/EXIT Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Two parallel sides Correcting picture distortionIi. See step iv below for further operation No parallel sides Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To select a picture mode that suits your need To reset the picture mode to the preset factory values Setting the User 1/User 2 modeResetting the picture mode Renaming user modes Fine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarity Adjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperature To leave and save the settings, press MENU/EXIT Setting Film ModeTo adjust and store the settings Color Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 display Freezing the image Utilizing FAQ functionHiding the image Press Enter Adjusting the sound level Adjusting the soundSetting the lamp mode Turning off the Power On/Off Ring Tone If you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environment Auto Source Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Menu item Category Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environment Highlight PIP and press / to select On Displaying more than one image source simultaneouslyTo display the PIP window PIP function is effective at below source combinations POWER/ON II again Turning the projector off On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup Display Setup Information Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Care of the projector Cleaning the lensCleaning the projector case Storing the projector Lamp information Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Indicators Power eventsLight Status & Description Troubleshooting Problem Cause Remedy Electrical SpecificationsOptical Terminals Dimensions Ceiling mount installationMm x 354.7 mm x 167 mm W x D x H Supported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHz Supported timing for Hdmi Hdcp input Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputs Warranty CopyrightDisclaimer