Resetting the lamp timer

7.Insert the replacement lamp. Make sure it is pushed fully and firmly in place.

8.Tighten the screw securing the lamp box. Reconnect the lamp connector.

9.Ensure the handle is fully locked in place.

10. Replace the lamp cover.

11.Tighten the screws on the lamp cover.

12.Reapply power and turn the projector back on.

English

Notes

•Please be careful to not over-tighten the screws.

•Loose screws may cause a bad connection, which could result in malfunction.

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.

Additional information

Page 55

Image 55

BenQ SH960 user manual Resetting the lamp timer

Contents

Welcome Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Overview Shipping contents Remote control operation Remote control batteriesCeiling mounting the projector Projector features Rear view Front and upper side viewUnder view Control panel Controls and functions Mute Remote controlOperating the Laser pointer Floor Rear Choosing a locationFloor Front Ceiling Front Obtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensions Height H Installation for a 43 ratio screenHighest Lens To use the lens shift lever Shifting the projection lens Component Connecting Hdmi devicesPreparations Terminal appearance Reference Picture quality Connecting S-Video or video devices Connecting component-video devices Connecting a monitor Connecting a computerConnect the projector to a computer with a VGA cable Preparations Turning the projector on Selecting an input source Using the OSD menuChanging Color Space Press MENU/EXIT twice* to leave and save the settings Using the menusUsing a security cable lock Use / to highlight the System Setup menu To leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the password Write down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password function Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image No parallel sides Correcting picture distortionIi. See step iv below for further operation Two parallel sides To select a picture mode that suits your need Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture mode Renaming user modes Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory values Fine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controls To set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant Color Color Management Setting Film ModeTo adjust and store the settings To leave and save the settings, press MENU/EXIT Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio image Press Enter Utilizing FAQ functionHiding the image Freezing the image Turning off the Power On/Off Ring Tone Adjusting the soundSetting the lamp mode Adjusting the sound level If you are in a non-DHCP environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environment Menu item Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Auto Source Category Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude Mode PIP function is effective at below source combinations Displaying more than one image source simultaneouslyTo display the PIP window Highlight PIP and press / to select On Turning the projector off POWER/ON II again On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Display System Setup Information Setup Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Storing the projector Cleaning the lensCleaning the projector case Care of the projector Getting to know the lamp hour Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Lamp information Replacing the lamp Timing of replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Power events IndicatorsLight Status & Description Problem Cause Remedy Troubleshooting Terminals SpecificationsOptical Electrical Ceiling mount installation DimensionsMm x 354.7 mm x 167 mm W x D x H KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC input Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Hdmi Hdcp input Copyright WarrantyDisclaimer