Reset Lamp Timer?

English

1.After the start-up logo, press MENU/EXIT and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Lamp Settings and press ENTER. The Lamp Settings page is displayed.

3.Highlight Reset Lamp Timer 1/Reset Lamp Timer 2 and press ENTER. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press ENTER. The lamp time will be reset to "0".

Advanced Setup

Lamp Settings	ENTER
HDMI Settings
Baud Rate	115200
High Altitude Mode	Off
Audio Settings
Password
Lan Control Settings
Reset All Settings
Direct Power On	Off
Signal Power On	Off
Expert Mode
S-Video	EXIT Back

Lamp Settings

Lamp Mode
Reset Lamp Timer 1	ENTER
Reset Lamp Timer 2
Equivalent Lamp Hour #1	50 hours
Equivalent Lamp Hour #2	50 hours
	EXIT Back

WARNING

Reset Cancel

56 Additional information

Page 56

Image 56

BenQ SH960 user manual Reset Lamp Timer?

Contents

Welcome Table of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Shipping contents Overview Ceiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Front and upper side viewRear view Controls and functions Control panel Operating the Laser pointer Remote controlMute Choosing a location Floor FrontCeiling Front Floor Rear Obtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screen Installation for a 43 ratio screen HighestLens Height H Shifting the projection lens To use the lens shift lever Connecting Hdmi devices PreparationsTerminal appearance Reference Picture quality Component Connecting component-video devices Connecting S-Video or video devices Connect the projector to a computer with a VGA cable Connecting a computerConnecting a monitor Turning the projector on Preparations Changing Color Space Using the OSD menuSelecting an input source Using the menus Using a security cable lockUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settings Utilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXIT Entering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting picture distortion Ii. See step iv below for further operationTwo parallel sides No parallel sides Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To select a picture mode that suits your need Setting the User 1/User 2 mode Resetting the picture modeTo reset the picture mode to the preset factory values Renaming user modes Fine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image clarity Setting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperature Setting Film Mode To adjust and store the settingsTo leave and save the settings, press MENU/EXIT Color Management About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 display Utilizing FAQ function Hiding the imageFreezing the image Press Enter Adjusting the sound Setting the lamp modeAdjusting the sound level Turning off the Power On/Off Ring Tone Configuring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment If you are in a non-DHCP environment Ii To switch input source, click on your desired signal Controlling the projector remotely through a web browserAuto Source Menu item Category Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environment Displaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinations POWER/ON II again Turning the projector off Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure System Setup Display Setup Information Function Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projector Setting Lamp Mode as Dual-Reliable Setting Auto Power OffLamp information Getting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp English Resetting the lamp timer Reset Lamp Timer? Light Status & Description IndicatorsPower events Troubleshooting Problem Cause Remedy Specifications OpticalElectrical Terminals Mm x 354.7 mm x 167 mm W x D x H DimensionsCeiling mount installation Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputs Disclaimer WarrantyCopyright