Manuals / Brands / TV and Video / TV Converter Box / Black Box / TV and Video / TV Converter Box

Black Box IC026A-R2, IC026AE-R2 Figure 4-10. Interface Converter Settings for Use with HP 7580A Plotter on a Macintosh.

1 71

Download 71 pages, 312.13 Kb

43

Figure 4-10. Interface Converter Settings for Use with HP 7580APlotter on a Macintosh.

After configuration, turn on the plotter and the interface converter. The

interface converter’s front-panel LEDs should all light momentarily while it

performs an internal ROM and RAM test. All LEDs should go out except for

the Power and Talk LED. The Talk LED indicates that the interface converter

has detected the plotter on the IEEE bus and has addressed it to listen.

When the serial host begins to send the interface converter data, the Receive

LED will flash. If it does not, this indicates that the interface is not receiving

data from the serial host. Verify the cables are connected properly and the

serial cable wiring. Verify the serial data format, word length, stop bits and

parity.

1 2 3 4 567 8

OPEN

SW2

Mode

Talk-Back on Timeout

Serial Term

C

Enabled

CR

Switch

Side

View

DOT

Echo

Parity

No Echo

No Parity

1 2 3 4 5 67 8

OPEN

SW3

IEEE Addr

IEEE Term

EOI

5

CR

Enabled

Switch

Side

View

DOT

Switch

Side

View

DOT

1 2 3 4 5 6 7 8

OPEN

SW1

Baud Rate

Handshake

Word Length

57600

X-ON/X-OFF

7 Data Bits

Talk-Back on Terminator Enabled

Stop Bits 1 Stop Bit

CHAPTER 4: Controller Operation

Contents

Main RS-232IEEE 488 INTERFACE CONVERTER EUROPEAN UNION DECLARATION OF CONFORMITY WARNING! Failure to follow these directives voids emission and immunity compliance. Page Page Page CONTENTS Contents RS-232IEEE 488 INTERFACE CONVERTER CONTENTS 1. Specifications WARNING! CHAPTER 1: Specifications CAUTION 2. Introduction 2.1 Description 2.2 Abbreviations CHAPTER 2: Introduction 3. Getting Started 3.1 Inspection 3.2 Configuration Figure 3-1. Factory-Default Settings. SW3 SW2 SW1 3.3 Serial Port Settings Figure 3-2. Switch SW1: Selecting the Serial Baud Rate. Figure 3-3. Switch SW1: Selecting the Serial Word Length (Data Bits). Figure 3-4. Switch SW1: Selecting the Serial Stop Bits. Figure 3-5. Switch SW2: Selecting the Serial Parity. Figure 3-6. Switch SW2: Enabling or Disabling Echo. Figure 3-7. Switch SW1: Selecting the Serial Handshake. 3.4 Selecting Terminator Substitution Figure 3-8. Switch SW2: Selecting the Serial Terminator. Figure 3-9. Switch SW3: Selecting the IEEE Bus Terminator. 3.5 Selecting the Mode Figure 3-10. Switch SW2: Selecting the Mode. 3.6 Selecting the IEEE Address Figure 3-11. Switch SW3: Selecting the IEEE Address. 3.7 Feature Selections Figure 3-12. Switch SW1: Enabling or Disabling Talk Back on Terminator in Controller Mode. Figure 3-13. Switch SW2: Enabling or Disabling Talk Back on Timeout in Controller Mode. Figure 3-14. Switch SW1: Enabling or Disabling SRQ on Last Serial Terminator in Peripheral Mode. 3.8 Serial Interface Figure 3-15. Selecting RS-232 or RS-422 Signal Levels. Figure 3-16. Rear View of the Interface Converters Serial Connector. Page Page 3.9 General CAUTION Page RS-232IEEE 488 INTERFACE CONVERTER 4.1 Controller-Mode (Serial to IEEE) Operation 4. Controller Operation 4.2 Serial and IEEE Terminator Substitution 4.3 IEEE Address Selection Figure 4-1. Switch SW3: Selecting the IEEE Address. 4.4 Talk-Back Features Figure 4-2. Switch SW1: Enabling or Disabling Talk-Back on Terminator. Figure 4-3. Switch SW2: Enabling or Disabling Talk-Back on Timeout. Page 4.5 Plotter Applications Figure 4-4. A PC-Based Graphics System. Figure 4-5. Selecting RS-232 Signal Levels. Figure 4-6. Interface Converter Settings for Use with HP 7580A Plotter on an IBM PC. SW2 SW3 SW1 Figure 4-7. MacPlot Configuration Screen. Figure 4-8. A Macintosh Based Graphics System. Interface Converter IEEE 488 RS-422 Page Figure 4-10. Interface Converter Settings for Use with HP 7580A Plotter on a Macintosh. Page 5. Peripheral Operation 5.1 Peripheral-Mode Operation 5.2 Serial and IEEE Input Buffers 5.3 IEEE Data Transfers Page RS-232IEEE 488 INTERFACE CONVERTER Figure 5-1. Switch SW1: Enabling or Disabling SRQ on Last Terminator. Figure 5-2. Serial Poll Status Byte. 5.4 Serial-Poll Status-Byte Register Page 5.5 Use of Serial and Bus Terminators 5.6 IEEE 488 Bus Implementation Page 5.7 IEEE Address Selection Figure 5-3. SW3 View for IEEE Address Selection. 6. IEEE 488 Primer 6.1 History 6.2 General Structure Page Figure 6-1. IEEE 488 Bus Structure. 6.3 Send It to My Address 6.4 Bus Management Lines 6.5 Handshake Lines Figure 6-2. IEEE Bus Handshaking. 6.6 Data Lines 6.7 Multiline Commands Page 6.8 More on Service Requests Page 7.1 Theory of Operation 7. Theory of Operation and Board Layout 7.2 Board Layout CHAPTER 7: Theory of Operation and Board Layout Figure 7-1. Component Layout of the Interface Converters Motherboard. Figure 7-2. Component Layout of the Interface Converters Serial I/O board. APPENDIX A: Sample Dumb-Terminal Program Appendix A. Sample Dumb-Terminal Program Appendix B. Character Codes and IEEE Multiline Messages Page Index INDEX