HD3, HD4, HD5 | Bosch Appliances MIC400AL instruction

MIC400 Series Camera Installation and Operation Manual

Table C - Composite cable to Power Supply HD-3 Connection Table

EN 16

Table E –Auxiliary connections (IR Lamps, PA Speakers and Heaters) to HD6

Composite		Function		Terminal Box		Terminal
Cable Wire				Connector		box ID
Colour						marking

Red		AC supply		HD3-1		Power

Green		AC supply rtn.		HD3-2		Power


White		Rx +		HD3-3		RxB

Yellow		Rx -		HD3-4		RxA

Drain Wire		Gnd		HD3-5		GND

Composite cable Wire colour

Brown

Grey

Function

Heater* or IR Lamps**

or PA speakers***

Heater* or IR Lamps**

or PA speakers***

Terminal Box Connector

HD6-1

HD6-2

Blue		Tx -		HD3-6		TxA

Violet		Tx +		HD3-7		TxB

Coax Core		Video		HD3-8		Video

Coax Screen		Video Return		HD3-9		Vid 0v

Black		Tamper Switch		HD3-10		Tamp Sw
(Optional)

Orange		Wash drive		HD3-11		Wash
(Optional)

Table D –Telemetry Connections to HD3, HD4 and HD5

*See page 19 for details on commissioning MIC400 cameras with the heater option fitted.

**IR power supplies only, see MIC-IR Power Supplies on page for more details.

*** See page 19 for details on connecting the PA speakers.

CAUTION: Connecting MIC400IR or MIC400PA units to a MIC-PSU with the heater option enabled as this can result in damage to the cameras. Please ensure that the heater link is disabled if a MIC400PA is to be used or ensure a MIC-IR-PSU is used with a MIC400IR camera unit.

Telemetry

Signal Name

RXB or Rx +

RXA or Rx -

GND

TXA or Tx -

TXB or Tx +

HD3

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

HD4

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

HD5

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Fuse ratings

The power supply houses 4 off 20mm fuses in fuse holders. The ratings for these fuses if fixed on the low voltage secondary side but changes with input voltage on the high voltage primary side.

The following table shows the fuse values fitted for the different supplies for operating the power supply:

Note FS 4 does not exist

Bosch Security Systems

Issue 1

Image 16

Bosch Appliances MIC400AL operation manual HD3, HD4, HD5

Contents

MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-240PSU MIC-115PSUMIC-24PSU MIC-12PSU MIC-WKT MIC-ALMMIC-BP3 MIC-BP4 Packaging Contents Unpacking Installation Environment Key to MIC-PMB drawing Associated Equipment & Typical Installations Installation Instructions Earthing of the MIC400 camera Underwater InstallationLightning Protection NON-IR Power Supply Units Electrical ConnectionsTable a MIC Composite Cable Pin table MIC-240PSU, MIC-24PSU and MIC-115 PSU Table B Power Connection to Header HD1 Power Supply Layout and ConnectionsPCB Earth Link HD4 HD3HD5 Bi-phase cards etc Rating for Primary Table G Power Input wiring connections for MIC-12PSU MIC-12PSU Power Supply Unit12 or 24 Volt vehicle supply Optional Cards and Kits for Non-IR MIC400 Cameras Commissioning MIC400PA and MIC400’s with heaters fittedMIC400PA Heater Option Bosch Security Systems Issue Setting the Power Supply Link Options MIC400IR Power Supply UnitsMIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU Figure D MIC-IR-240PSU Layout Table I Fuse Ratings for MIC-IR-240PSU Function Type Signal Table K -IR Lamp Connections HD6Terminal Box ID Marking Table L -Washer Pump Connection HD7 MIC-IR-12PSU Figure E MIC-IR-12PSU Schematic Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Installation Instructions Connecting the MIC400 to the PC Connecting the Greenwich AdaptorTable N Connecting the Greenwich Adaptor Adaptor Connections Connecting the KK systems K2-ADE RS232 to RS485/422 Adaptor DIP SwitchSetting Table O K2-ADE Adaptor connections MIC Power Supply Converter Output Telemetry Header Table Q MIC-USB485CVTR Connection Table and DiagramCommunication Mode Commissioning the MIC400 through Universal Camset MIC-USB485CVTR and Universal Camset Software InstallationStandard Controls Boot Messages MIC Settings Camset Settings Reset Camset Manual Control Pan, Tilt and Zoom ControlsIris Controls Focus Controls Preset Positions Auxiliaries Tour Controls Soft Stops and Non Dwell Zones MIC Setups General SettingsPan Reverse Tilt Reverse Auto Home Controls Default Settings Other controls Multi Alarm Settings Privacy and Captions Frame Integration SettingsLens Recalibration and Frame Integration Privacy Controls Privacy Calibration Captions Thermal Advanced Settings Temperature and HumidityTimers Clear All Statistics Eeprom Copier Download Eeprom To FileUpload Eeprom From File Remap Auxiliary Pelco Only Menu Controls Panasonic Only POT TestMatrix Controls Pot Test Controls Pot Test Results Send Direct Command Comms Communications Testing AlarmsMIC Comms Cam Comms SonySet Preset Number Get Preset from MICSend Preset to MIC Sony Set Execute this Preset Load Table from File to MICSave Table from MIC to File Clear Table Table R Sonyset Commands MIC Programmer Bosch Security Systems Issue Alarms Camera ModuleOperational Communication & Protocols Accessories PhysicalEnvironmental Electrical MIC400PA Twin Speakers MIC400UL and MIC400UT MIC400S MIC400IR IR Illuminators Dimension Drawings Contact Americas Europe, Middle East, AfricaAsia-Pacific Bosch Security Systems Inc Preset Codes Appendix a Protocol Preset codesPelco Bosch Security Systems Special Setup Presets Vision Bosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2