Important Safety Instructions | Bosch Appliances MIC400AL manual

MIC400 Series Camera Installation and Operation Manual

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions

2.Keep these instructions

3.Heed all warnings

4.Follow all instructions

5.Install according to manufacturer’s instructions

6.Do not install near any strong heat sources such as furnaces

7.Do not open the camera unit, doing so invalidates the unit’s warranty

8.Do not back-drive the pan or tilt axis of the camera. To do so will damage the motor drive gear chain and will invalidate the warranty

9.Do not use caustic or abrasive cleaning products on the unit

10.Do not point the MIC400 camera at the sun. BOSCH Group will not be liable for any damages to cameras which have been directly pointed at the sun

11.In situations where there could be a risk of injury should any part of the assembly become detached for any reason and fall, normal common sense safety precautions should be employed; a strong safety chain between the camera pan shaft and the mounting surface is recommended

12.For transportation please rotate the ball so the window points towards the base, this helps to protect the wiper & windows during transit

13.Ensure that the product case is properly earthed. If the product is likely to be struck by lightning, ensure that earth-bonding connections are made correctly to the mounting base of the unit

14.Use only the power sources indicated in this user guide and ensure that the current rating of the supply cable is adequate for the product

15.Do not stand canted (45°) MIC400’s upright as they can be easily knocked over, lay them on their side.

EN 5

This product complies with the following EC directives:-

EMC Directive (89/336/EC as amended)

Machinery Directive (98/37/EC)

LV Directive (73/23/EC)

RoHS (Restriction of Hazardous Substances) 2002/95/EC

WEEE (Waste Electrical & Electronic Equipment) 2002/96/EC

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local supplier for procedures for recycling this equipment.

Bosch Security Systems

Issue 1

Image 5

Bosch Appliances MIC400AL operation manual Important Safety Instructions

Contents

MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-115PSU MIC-240PSUMIC-24PSU MIC-12PSU MIC-ALM MIC-WKTMIC-BP3 MIC-BP4 Unpacking Packaging Contents Installation Environment Key to MIC-PMB drawing Installation Instructions Associated Equipment & Typical Installations Lightning Protection Underwater InstallationEarthing of the MIC400 camera Electrical Connections NON-IR Power Supply UnitsTable a MIC Composite Cable Pin table MIC-240PSU, MIC-24PSU and MIC-115 PSU PCB Earth Link Power Supply Layout and ConnectionsTable B Power Connection to Header HD1 HD5 HD3HD4 Rating for Primary Bi-phase cards etc 12 or 24 Volt vehicle supply MIC-12PSU Power Supply UnitTable G Power Input wiring connections for MIC-12PSU Commissioning MIC400PA and MIC400’s with heaters fitted Optional Cards and Kits for Non-IR MIC400 CamerasMIC400PA Heater Option Bosch Security Systems Issue MIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU MIC400IR Power Supply UnitsSetting the Power Supply Link Options Table I Fuse Ratings for MIC-IR-240PSU Function Type Figure D MIC-IR-240PSU Layout Table K -IR Lamp Connections HD6 SignalTerminal Box ID Marking Table L -Washer Pump Connection HD7 MIC-IR-12PSU Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Figure E MIC-IR-12PSU Schematic Installation Instructions Connecting the Greenwich Adaptor Connecting the MIC400 to the PCTable N Connecting the Greenwich Adaptor Adaptor Connections DIP Switch Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorSetting Table O K2-ADE Adaptor connections Communication Mode Table Q MIC-USB485CVTR Connection Table and DiagramMIC Power Supply Converter Output Telemetry Header Standard Controls MIC-USB485CVTR and Universal Camset Software InstallationCommissioning the MIC400 through Universal Camset MIC Settings Boot Messages Camset Settings Manual Control Pan, Tilt and Zoom Controls Reset CamsetIris Controls Focus Controls Auxiliaries Preset Positions Soft Stops and Non Dwell Zones Tour Controls General Settings MIC SetupsPan Reverse Tilt Reverse Auto Home Controls Other controls Default Settings Multi Alarm Settings Lens Recalibration and Frame Integration Frame Integration SettingsPrivacy and Captions Privacy Controls Captions Privacy Calibration Thermal Temperature and Humidity Advanced SettingsTimers Clear All Statistics Download Eeprom To File Eeprom CopierUpload Eeprom From File Remap Auxiliary Pelco Only Matrix Controls POT TestMenu Controls Panasonic Only Pot Test Results Pot Test Controls Comms Send Direct Command Alarms Communications TestingMIC Comms Cam Comms Get Preset from MIC SonySet Preset NumberSend Preset to MIC Sony Set Load Table from File to MIC Execute this PresetSave Table from MIC to File Clear Table Table R Sonyset Commands MIC Programmer Bosch Security Systems Issue Camera Module AlarmsOperational Communication & Protocols Physical AccessoriesEnvironmental Electrical Twin Speakers MIC400PA MIC400UL and MIC400UT MIC400S IR Illuminators MIC400IR Dimension Drawings Europe, Middle East, Africa Contact AmericasAsia-Pacific Bosch Security Systems Inc Pelco Appendix a Protocol Preset codesPreset Codes Bosch Security Systems Vision Special Setup Presets Bosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2