Multi Alarm Settings | Bosch Appliances MIC400AL guide

MIC400 Series Camera Installation and Operation Manual

Save Current MIC Settings

This option will first prompt for a file location and then store the current state of all the options outlined above to an XML file which can then be loaded at a later date back into Camset as a standard for a specific site.

Load Settings into Camset

This will prompt to open an XML file as saved above. Only valid Camset Default XML files will work.

Set Current Settings to MIC

This will go through each of the settings above except for thermal, and send out the commands to the MIC to set it up as Camset displays. This may take a few seconds as there are several commands involved in this process.

Upload Default Options

At the end of this there are 2 extra options for defaults, Clear SS and NDZ will clear any saved Soft Stops and Non-Dwell Zones and then Find End Stops. These options may be used to completely set up a MIC after it has been reprogrammed to a new protocol.

EN 39

Multi Alarm Settings

Learn Alarm Positions

Simply point the MIC400 at the position you would like it to cover when each numbered alarm is triggered and press Learn Alarm Position to set this.

Relay State, Activation and Re-arm

This function is available only to MIC-400’s with the MIC-ALM card fitted or the MIC400IR Power Supply which has Four (4) Alarm Inputs built in.

The MIC-ALM multi alarm card provides 2 output relays which can be configured to close or open on given alarm inputs. Relay 1 can be activated from either alarm inputs 1 to 4 or 1 to 8 and relay 2 with alarm inputs 5 to 8 or 1 to 8.

Bosch Security Systems

Issue 1

Image 39

Bosch Appliances MIC400AL operation manual Multi Alarm Settings

Contents

MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-12PSU MIC-240PSUMIC-115PSU MIC-24PSU MIC-BP4 MIC-WKTMIC-ALM MIC-BP3 Unpacking Packaging Contents Installation Environment Key to MIC-PMB drawing Installation Instructions Associated Equipment & Typical Installations Underwater Installation Earthing of the MIC400 cameraLightning Protection MIC-240PSU, MIC-24PSU and MIC-115 PSU NON-IR Power Supply UnitsElectrical Connections Table a MIC Composite Cable Pin table Power Supply Layout and Connections Table B Power Connection to Header HD1PCB Earth Link HD3 HD4HD5 Rating for Primary Bi-phase cards etc MIC-12PSU Power Supply Unit Table G Power Input wiring connections for MIC-12PSU12 or 24 Volt vehicle supply Heater Option Optional Cards and Kits for Non-IR MIC400 CamerasCommissioning MIC400PA and MIC400’s with heaters fitted MIC400PA Bosch Security Systems Issue MIC400IR Power Supply Units Setting the Power Supply Link OptionsMIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU Table I Fuse Ratings for MIC-IR-240PSU Function Type Figure D MIC-IR-240PSU Layout Table L -Washer Pump Connection HD7 SignalTable K -IR Lamp Connections HD6 Terminal Box ID Marking MIC-IR-12PSU Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Figure E MIC-IR-12PSU Schematic Installation Instructions Adaptor Connections Connecting the MIC400 to the PCConnecting the Greenwich Adaptor Table N Connecting the Greenwich Adaptor Table O K2-ADE Adaptor connections Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorDIP Switch Setting Table Q MIC-USB485CVTR Connection Table and Diagram MIC Power Supply Converter Output Telemetry HeaderCommunication Mode MIC-USB485CVTR and Universal Camset Software Installation Commissioning the MIC400 through Universal CamsetStandard Controls MIC Settings Boot Messages Camset Settings Focus Controls Reset CamsetManual Control Pan, Tilt and Zoom Controls Iris Controls Auxiliaries Preset Positions Soft Stops and Non Dwell Zones Tour Controls Tilt Reverse MIC SetupsGeneral Settings Pan Reverse Auto Home Controls Other controls Default Settings Multi Alarm Settings Frame Integration Settings Privacy and CaptionsLens Recalibration and Frame Integration Privacy Controls Captions Privacy Calibration Thermal Clear All Statistics Advanced SettingsTemperature and Humidity Timers Remap Auxiliary Pelco Only Eeprom CopierDownload Eeprom To File Upload Eeprom From File POT Test Menu Controls Panasonic OnlyMatrix Controls Pot Test Results Pot Test Controls Comms Send Direct Command Cam Comms Communications TestingAlarms MIC Comms Sony Set SonySet Preset NumberGet Preset from MIC Send Preset to MIC Clear Table Execute this PresetLoad Table from File to MIC Save Table from MIC to File Table R Sonyset Commands MIC Programmer Bosch Security Systems Issue Communication & Protocols AlarmsCamera Module Operational Electrical AccessoriesPhysical Environmental Twin Speakers MIC400PA MIC400UL and MIC400UT MIC400S IR Illuminators MIC400IR Dimension Drawings Bosch Security Systems Inc Contact AmericasEurope, Middle East, Africa Asia-Pacific Appendix a Protocol Preset codes Preset CodesPelco Bosch Security Systems Vision Special Setup Presets Bosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2