Table K -IR Lamp Connections HD6 | Bosch Appliances MIC400AL

MIC400 Series Camera Installation and Operation Manual		EN 23
Table J - Alarm Input header for MIC-IR Power Supplies HD2	Installation Instructions

Connection

HD2 pin 1

HD2 pin 2

HD2 pin 3

HD2 pin 4

HD2 pin 5

HD2 pin 6

HD2 pin 7

HD2 pin 8

Function

Alarm 1

0v

Alarm 2

0v

Alarm 3

0v

Alarm 4 0v

WARNING: Electrical Danger: Ensure all power is disconnected before opening or working upon any Power Supply Unit.

Installation must be carried out by suitably qualified persons & all local safety regulations should be followed.

After removal of the lid take care of components C7, C9 and IC2 heatsink. In normal operation these components can reach a temperature of 55 Deg C.

To install the MIC-IR-240PSU and MIC-IR-115PSU please do the following:-

1. Locate the mounting position of the MIC-PSU so that it cannot be

interfered with either intentionally or accidentally, a lockable cabinet is

recommended.

Table K –IR Lamp Connections HD6

Composite cable Wire colour.

Brown

Grey

Function

IR Lamp

+

IR Lamp -

Terminal

Box

Connector

HD6-1

HD6-2

Terminal

box ID

marking.

IR+

IR-

2.	Securely fix the MIC-PSU using M4 stainless steel screws & washers;
	ensure the cable glands have sufficient room to allow for the cables to
	enter.
3.	Feed all cabling through the appropriate sized gland holes.
4.	Connect the composite cable to HD3 following the colour coding as shown
	in the Table B & printed on the PCB, connect all wires.
5.	Connect the Brown and Grey wires for the IR lamps to HD6 as per Table J

Table L –Washer Pump Connection HD7

6.	Connect the Coaxial video cable to the CN1 header.
7.	If alarms are to be used connect these to HD2 as per Table I above

	Signal		Connection
			HD7 pin 1

	Washer pump Live
			HD7 pin 2
	Washer pump Neutral		HD7 pin 2

Ident

L

N

8.	Telemetry connections are provided by headers HD3, HD4 and HD5 which
	respectively enable crimp or screw terminations for connecting the MIC400
	to the control room.
9.	Connect the power to HD1 carefully observing the polarity and voltage as
	per Table A.

Bosch Security Systems

Issue 1

Image 23

Bosch Appliances MIC400AL Table K -IR Lamp Connections HD6, Terminal Box ID Marking, Table L -Washer Pump Connection HD7

Contents

MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-12PSU MIC-240PSUMIC-115PSU MIC-24PSU MIC-BP4 MIC-WKTMIC-ALM MIC-BP3 Unpacking Packaging Contents Installation Environment Key to MIC-PMB drawing Installation Instructions Associated Equipment & Typical Installations Lightning Protection Underwater InstallationEarthing of the MIC400 camera MIC-240PSU, MIC-24PSU and MIC-115 PSU NON-IR Power Supply UnitsElectrical Connections Table a MIC Composite Cable Pin table PCB Earth Link Power Supply Layout and ConnectionsTable B Power Connection to Header HD1 HD5 HD3HD4 Rating for Primary Bi-phase cards etc 12 or 24 Volt vehicle supply MIC-12PSU Power Supply UnitTable G Power Input wiring connections for MIC-12PSU Heater Option Optional Cards and Kits for Non-IR MIC400 CamerasCommissioning MIC400PA and MIC400’s with heaters fitted MIC400PA Bosch Security Systems Issue MIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU MIC400IR Power Supply UnitsSetting the Power Supply Link Options Table I Fuse Ratings for MIC-IR-240PSU Function Type Figure D MIC-IR-240PSU Layout Table L -Washer Pump Connection HD7 SignalTable K -IR Lamp Connections HD6 Terminal Box ID Marking MIC-IR-12PSU Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Figure E MIC-IR-12PSU Schematic Installation Instructions Adaptor Connections Connecting the MIC400 to the PCConnecting the Greenwich Adaptor Table N Connecting the Greenwich Adaptor Table O K2-ADE Adaptor connections Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorDIP Switch Setting Communication Mode Table Q MIC-USB485CVTR Connection Table and DiagramMIC Power Supply Converter Output Telemetry Header Standard Controls MIC-USB485CVTR and Universal Camset Software InstallationCommissioning the MIC400 through Universal Camset MIC Settings Boot Messages Camset Settings Focus Controls Reset CamsetManual Control Pan, Tilt and Zoom Controls Iris Controls Auxiliaries Preset Positions Soft Stops and Non Dwell Zones Tour Controls Tilt Reverse MIC SetupsGeneral Settings Pan Reverse Auto Home Controls Other controls Default Settings Multi Alarm Settings Lens Recalibration and Frame Integration Frame Integration SettingsPrivacy and Captions Privacy Controls Captions Privacy Calibration Thermal Clear All Statistics Advanced SettingsTemperature and Humidity Timers Remap Auxiliary Pelco Only Eeprom CopierDownload Eeprom To File Upload Eeprom From File Matrix Controls POT TestMenu Controls Panasonic Only Pot Test Results Pot Test Controls Comms Send Direct Command Cam Comms Communications TestingAlarms MIC Comms Sony Set SonySet Preset NumberGet Preset from MIC Send Preset to MIC Clear Table Execute this PresetLoad Table from File to MIC Save Table from MIC to File Table R Sonyset Commands MIC Programmer Bosch Security Systems Issue Communication & Protocols AlarmsCamera Module Operational Electrical AccessoriesPhysical Environmental Twin Speakers MIC400PA MIC400UL and MIC400UT MIC400S IR Illuminators MIC400IR Dimension Drawings Bosch Security Systems Inc Contact AmericasEurope, Middle East, Africa Asia-Pacific Pelco Appendix a Protocol Preset codesPreset Codes Bosch Security Systems Vision Special Setup Presets Bosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2