MIC400PA, Heater Option | Bosch Appliances MIC400AL guide

MIC400 Series Camera Installation and Operation Manual

EN 19

Optional Cards and Kits for Non-IR MIC400 Cameras

The MIC400 has several optional cards and kits as described earlier.

Please refer to the respective manuals for details on their installation and operation.

MIC-WKTWasher bracket, nozzle and pump card kit for non-ir cameras

MIC-ALM8-input alarm card for non-ir cameras, includes washer pump drive function

MIC-BP3Bosch Bi-phase converter card for MIC-power supplies without an expansion slot available including all IR psu’s

MIC-BP4Bosch Bi-phase converter card for MIC power supplies with an available expansion slot.

Commissioning MIC400PA and MIC400’s with heaters fitted.

MIC400PA

The MIC400PA has two (2) 6w, 8ohm, IP67 rated speakers connected in series to allow for public address applications, these utilise the Brown and Grey wires on the composite cable that are normally used for IR illuminators.

There are no connections for speakers on the power supply itself; the speakers are connected directly to a third party amplifier and microphone.

To utilise the speakers please do the following:-

1.Disconnect the power supply from the power source; locate the Brown and Grey wires in the composite cable.

2.Using a terminal block connect the Brown and Grey wires from the speakers.

3.Feed the speaker cable through one of the conduit glands in the PSU enclosure.

4.Connect the speaker cable from a third party amplifier and microphone to permit the speakers to be used.

Heater Option

Applicable to the following power supplies only.

MIC-240PSU, MIC-115PSU, MIC-24PSU and MIC-12PSU only.

There are two links on the power supply printed circuit board which must be changed to allow heater operation. Please do the following to enable the heaters to function:-

1.Disconnect the power supply from the power source; locate the Brown and Grey wires from the composite cable.

2.Locate the PCB links next to HD6, the default setting is 0V (shown below)

Bosch Security Systems

Issue 1

Image 19

Bosch Appliances MIC400AL operation manual Optional Cards and Kits for Non-IR MIC400 Cameras, MIC400PA, Heater Option

Contents

MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-12PSU MIC-240PSUMIC-115PSU MIC-24PSU MIC-BP4 MIC-WKTMIC-ALM MIC-BP3 Unpacking Packaging Contents Installation Environment Key to MIC-PMB drawing Installation Instructions Associated Equipment & Typical Installations Earthing of the MIC400 camera Underwater InstallationLightning Protection MIC-240PSU, MIC-24PSU and MIC-115 PSU NON-IR Power Supply UnitsElectrical Connections Table a MIC Composite Cable Pin table Table B Power Connection to Header HD1 Power Supply Layout and ConnectionsPCB Earth Link HD4 HD3HD5 Rating for Primary Bi-phase cards etc Table G Power Input wiring connections for MIC-12PSU MIC-12PSU Power Supply Unit12 or 24 Volt vehicle supply Heater Option Optional Cards and Kits for Non-IR MIC400 CamerasCommissioning MIC400PA and MIC400’s with heaters fitted MIC400PA Bosch Security Systems Issue Setting the Power Supply Link Options MIC400IR Power Supply UnitsMIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU Table I Fuse Ratings for MIC-IR-240PSU Function Type Figure D MIC-IR-240PSU Layout Table L -Washer Pump Connection HD7 SignalTable K -IR Lamp Connections HD6 Terminal Box ID Marking MIC-IR-12PSU Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Figure E MIC-IR-12PSU Schematic Installation Instructions Adaptor Connections Connecting the MIC400 to the PCConnecting the Greenwich Adaptor Table N Connecting the Greenwich Adaptor Table O K2-ADE Adaptor connections Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorDIP Switch Setting MIC Power Supply Converter Output Telemetry Header Table Q MIC-USB485CVTR Connection Table and DiagramCommunication Mode Commissioning the MIC400 through Universal Camset MIC-USB485CVTR and Universal Camset Software InstallationStandard Controls MIC Settings Boot Messages Camset Settings Focus Controls Reset CamsetManual Control Pan, Tilt and Zoom Controls Iris Controls Auxiliaries Preset Positions Soft Stops and Non Dwell Zones Tour Controls Tilt Reverse MIC SetupsGeneral Settings Pan Reverse Auto Home Controls Other controls Default Settings Multi Alarm Settings Privacy and Captions Frame Integration SettingsLens Recalibration and Frame Integration Privacy Controls Captions Privacy Calibration Thermal Clear All Statistics Advanced SettingsTemperature and Humidity Timers Remap Auxiliary Pelco Only Eeprom CopierDownload Eeprom To File Upload Eeprom From File Menu Controls Panasonic Only POT TestMatrix Controls Pot Test Results Pot Test Controls Comms Send Direct Command Cam Comms Communications TestingAlarms MIC Comms Sony Set SonySet Preset NumberGet Preset from MIC Send Preset to MIC Clear Table Execute this PresetLoad Table from File to MIC Save Table from MIC to File Table R Sonyset Commands MIC Programmer Bosch Security Systems Issue Communication & Protocols AlarmsCamera Module Operational Electrical AccessoriesPhysical Environmental Twin Speakers MIC400PA MIC400UL and MIC400UT MIC400S IR Illuminators MIC400IR Dimension Drawings Bosch Security Systems Inc Contact AmericasEurope, Middle East, Africa Asia-Pacific Preset Codes Appendix a Protocol Preset codesPelco Bosch Security Systems Vision Special Setup Presets Bosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2