Bosch Power Tools CM10GD manual Reaching with Your Hand Under a Coasting Blade is Dangerous

BM 2610027879 07-13_BM 2610027879 07-13.qxp 7/8/13 9:51 AM Page 4

Safety

!WARNING “READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (l) symbol listed BELOW, and other safety precautions, may result in serious personal

injury.

•Do not use the saw until the table is clear of

all tools, wood scraps, etc., except the work- piece. Small debris, loose pieces of wood or other objects that contact the revolving blade can be thrown with high speed at the operator.

•Do not feed workpiece into the blade or cut “freehand” in any way. Workpiece must be stationary and clamped or braced by your hand. Saw must be fed through the workpiece smoothly and at a rate which will not overload the saw’s motor.

•Cut only one workpiece at a time. Multiple workpieces cannot be adequately clamped or braced and may bind on the blade or shift dur- ing cutting.

•Be certain the miter saw is mounted or placed on a level, firm work surface before using. A level and firm work surface reduces the risk of the miter saw becoming unstable.

•plan your work. provide adequate support accessories such as tables, saw horses, table extension, etc. for workpieces wider or longer than the table top (see page 29). Workpieces longer or wider than the miter saw table can tip if not securely supported. If the cutoff piece or workpiece tips, it can lift the lower guard or be thrown by the spinning blade.

•Do not use another person as a substitute for a table extension or as additional sup- port. Unstable support for the workpiece can cause the blade to bind or the workpiece to shift during the cutting operation, pulling you and the helper into the spinning blade.

•The cutoff piece must not be jammed or pressured by any other means against the spinning saw blade. If confined, i.e., using length stops, it could get wedged against the blade and thrown violently.

•Always use a clamp or a fixture designed to properly support round material such as dowel rods or tubing. Rods have a tendency to roll while being cut, causing the blade to “bite” and pull the work with your hand into the blade.

•When cutting irregularly shaped work- pieces, plan your work so it will not slip and pinch the blade and be torn from your hand. A piece of molding, for example, must lie flat or be held by a fixture or jig that will not let it twist, rock or slip while being cut.

•let the blade reach full speed before con- tacting the workpiece. This will help avoid thrown workpieces.

•If the workpiece or blade becomes jammed or bogged down, turn miter saw “Off” by releasing switch. Wait for all moving parts to stop and unplug the miter saw, then work to free the jammed material. Continued saw- ing with jammed workpiece could cause loss of control or damage to miter saw.

•Braking action of the saw causes the saw head to jerk downward. Be ready for this reaction when making an incomplete cut or when releasing the switch before the head is completely in the DOWN position.

•After finishing the cut, release the switch, hold the saw arm down and wait for blade to stop before removing work or cutoff piece. If blade does not stop within five (5) sec- onds, unplug the saw and follow the instruc- tions in the Troubleshooting section.

REACHING WITH YOUR HAND UNDER A COASTING BLADE IS DANGEROUS!

•There are additional safety instructions for particular operations of the saw in the Saw Operations section. Read the rest of the manual for safe operation.

•The CM10GD miter saw has an extremely smooth action and requires the operator to firmly grip the handle before turning “ON” the saw. for slide-action cutting, first grip the switch handle in the Up position and pull out back to the fully extended position. The blade must clear the workpiece. Make certain the clamp does not interfere with the guard and head assembly. Second, turn saw “ON” and lower the saw to the table. Then pUSH saw through the workpiece. Release the switch and wait for the blade to completely stop before raising the head assembly and removing the workpiece. Never “pullcut,” since blade may climb the workpiece, causing KICKBACK.

•for chop-action cutting, move the head assembly to the rear as far as it will go and engage the mechanism lock. Then turn the saw “ON” and lower the head assembly to make the cut. Release the switch and wait for the blade to completely stop before raising the head assembly and removing the workpiece. Failure to lock the mechanism can cause the blade to suddenly climb up on the top of the workpiece and force itself toward you.

“SAVE THESE INSTRUCTIONS”

4.