|
|
|
| Trouble shooting guide | |
|
|
|
|
|
|
| CONDITION/Problem | THINGS TO CHECK |
| SOLUTION |
|
|
|
|
|
|
|
1- | Unit will not power up/ | Outlet |
| Make sure outlet is functioning correctly. Verify this by |
|
| turn on/start |
|
| plugging another object (ex: lamp) into the outlet. If outlet |
|
|
|
|
| is connected to a light switch, check to make sure it is on. |
|
|
|
|
| If outlet is not functioning find a working outlet. |
|
|
| Power cord not plugged |
| Make sure the power cord is firmly secured to A/C inlet on |
|
|
| in. |
| the front of the unit and firmly inserted into a |
|
|
|
|
| socket. |
|
|
| Power switch turned off. |
| Make sure the power switch at the rear of the unit is in the |
|
|
|
|
| “ON” position. |
|
|
| Safety key not plugged in. |
| Plug Safety Key into magnetic safety key location on |
|
|
|
|
| display. (See Emergency Stop Procedure within the |
|
|
|
|
| Important Safety Precautions section) |
|
|
| Safety key magnet not |
| Try another magnet if available, such as refrigerator |
|
|
| functioning. |
| magnet. If unit works with different magnet replace |
|
|
|
|
| safety key. |
|
|
| LED Diagnostic needed. |
| Access diagnostic LEDs on motor controller board by |
|
|
|
|
| following the instructions in the TC5300/6000 Diagnostics. |
|
|
|
|
| Caution: Machine is on. Current is active!!. |
|
|
|
|
| Check the B & G LEDs for the following: |
|
|
|
|
| If neither B nor G are lit power is not reaching the motor |
|
|
|
|
| controller. Disconnect unit from power source and check |
|
|
|
|
| wiring integrity and connections between A/C inlet |
|
|
|
|
| (where cord plugs in to machine) and motor controller |
|
|
|
|
| board. If any visible damage replace A/C junction kit. If |
|
|
|
|
| light G is lit but light B is not lit replace motor controller |
|
|
| I/O Cables |
| If LEDs B & G are both lit check connections and for signs |
|
|
|
|
| of visible damage to any of the three I/O calbes. If no |
|
|
|
|
| visible damage check continuity using a |
|
|
|
|
|
|
|
|
| Console control board |
| If I/O cables are all functioning properly, LEDs B & G are |
|
|
|
|
| lit up, and machine still will not power up replace upper |
|
|
|
|
| console control board |
|
2 | Speed displayed is not | Display set to wrong |
| Change display units. (See Console Display & Set Up |
|
| accurate. | unit of measure. |
| section) |
|
|
| (English/Metric) |
|
|
|
|
| Out of calibration. |
|
| |
|
|
|
|
|
|
3 | Heart rate not displayed | Transmitter not making |
| Moisten skin contact area on the chest strap. (See Heart |
|
| while using chest strap. | good contact with skin. |
| Rate Monitoring Pg. 23) |
|
|
| Electromagnetic |
| Turn off any television, AM radio, microwave, or computer |
|
|
| interference. |
| within 6 feet (2 meters) of theTreadClimber® fitness |
|
|
|
|
| machine. |
|
|
| Chest strap transmitter. |
| Test chest strap with another HR monitoring device such |
|
|
|
|
| as HR watch, machine at a gym. If transmitter has good |
|
|
|
|
| skin contact and still is not found to be emitting HR signal |
|
|
|
|
| replace chest strap transmitter. |
|
|
|
| Bowflex® TreadClimber® Assembly and Owner’s Manual 61 |