Figure 16: Secure Brackets to Horizontal Channel
5.Add front/center section mounting hardware to all but one (1) horizontal support channel assembly.
Lay channel assembly on floor with brackets facing up, see Figure 17a. Install hardware as shown with two (2) washers and two (2) 1/2” lg. spacers between bracket legs and one (1) washer and one (1) hex nut on each end of 3/8”
6.Add rear section mounting hardware to remaining horizontal support channel assembly. Lay channel assembly on floor with brackets facing up, see
Figure 17b. Install hardware as shown with one
(1) 1-3/4” lg. spacer between bracket legs, one (1) washer and one (1) hex nut on one end of 3/8” -16 x 13-3/8” lg. threaded rod, with one (1) washer,
Table VIII: Frame/Bracket Mounting Locations
one (1)
(1) hex nut on the opposite end of rod. Repeat for second bracket, refer to assembled end view in Figure 17b.
7.Mount front/center horizontal channel assembly(lies) to appropriate casting(s) on block assembly as outlined in Table VIII. Position threaded rods on channel assemblies over slotted lugs on casting as shown in Figure 18a. Spread inside washers until rod drops to bottom of slot as shown in Figure 18a, Detail ‘A’. Hand tighten nuts, make sure washers engage casting below washer retaining lugs, see Detail B. Repeat for all remaining bracket attachment points.
8.Mount rear horizontal channel assembly to rear section and adjacent center section as shown in Figure 18b. Position assembly behind supply manifold, spread washers and lower threaded rod into slotted openings on both castings as shown in Figure 18b, Detail A. Hand tighten nuts, make sure washers engage casting below washer retaining lugs as shown in Detail B. Repeat for opposite side.
9.Wrench tighten hex nuts on all channel assemblies making sure rods are fully seated in slotted openings.
10.Locate and install lower front/center section brackets to casting legs. Brackets are universal and can be used on either side of block assembly. Refer to Table VIII for appropriate casting leg to be used for bracket attachment. Brackets mount to rear surface of leg with offset toward the rear as shown in Figure 19. Hold bracket at a 45° angle while engaging upper slot over threaded tie rod, rotate bracket around rod until lower slot is aligned with lower hole in casting leg. Insert 5/8
Boiler Size |
| Front | f | Block Assembly | g | Rear |
| |
|
|
|
|
|
|
| ||
Frame 1 | Frame 2 | Frame 3 | Frame 4 | Frame 5 | ||||
| ||||||||
|
|
|
|
|
|
| ||
4 Section | Front Section | Rear Section |
| |||||
|
|
|
|
|
|
| ||
5 Section | Front Section | Rear Section |
| |||||
|
|
|
|
|
|
| ||
6 Section | Front Section | Rear Section |
| |||||
|
|
|
|
|
|
| ||
7 Section | Front Section | Section 4 | Rear Section |
| ||||
|
|
|
|
|
|
| ||
8 Section | Front Section | Section 5 | Rear Section |
| ||||
|
|
|
|
|
|
| ||
9 Section | Front Section | Section 5 | Rear Section |
| ||||
|
|
|
|
|
|
| ||
10 Section | Front Section | Section 6 | Rear Section |
| ||||
|
|
|
|
|
|
| ||
11 Section | Front Section | Section 6 | Rear Section |
| ||||
12 Section | Front Section | Section 5 | Section 9 | Rear Section | ||||
13 Section | Front Section | Section 5 | Section 9 | Rear Section | ||||
14 Section | Front Section | Section 5 | Section 10 | Rear Section | ||||
15 Section | Front Section | Section 6 | Section 11 | Rear Section | ||||
16 Section | Front Section | Section 6 | Section 11 | Rear Section | ||||
17 Section | Front Section | Section 5 | Section 9 | Section 13 | Rear Section | |||
18 Section | Front Section | Section 5 | Section 10 | Section 14 | Rear Section |
31