Cabletron Systems 2200 RELATED DOCUMENTS

Related Documents

xvi

Chapter 3,

Installation

, provides instructions on how to install the 2E253-49R and connect

segments to the device.

Chapter 4,

Troubleshooting

, describes the function of the LANVIEW LEDs, which can help to

quickly diagnose network/operational problems.

Appendix A,

Speciﬁcations

, contains information on functionality and operating speciﬁcations,

connector pinouts, environmental requirements, and physical properties.

Appendix B,

Optional Installations and Mode Switch Bank Settings

, describes how to remove

the cover from the device, set the Mode Switch, and shows the location of an optional High Speed

Interface Module (HSIM) or Very High Speed Interface Module (VHSIM).

RELATED DOCUMENTS

The following Cabletron Systems documents may help to set up and manage the 2E253-49R:

•

SmartSwitch Series 2E253, 2H252, 2H253, and 2H258 Local Management User’s Guide

•

Ethernet Technology Guide

•

Cabling Guide

•

SmartTrunk User’s Guide

•

WAN Series Local Management User’s Guide

The following are Cabletron Systems documents associated with optional interface modules:

•

HSIM-A6DP User’s Guide

•

HSIM-F6 User’s Guide

•

HSIM-FE6 User’s Guide

•

HSIM-W6 Installation Guide

•

HSIM-W84 Installation Guide

•

HSIM-W87 User’s Guide

•

HSIM-G01/G09 User’s Guide

•VHSIM-G6 User’s Guide

•VHSIM-A6DP User’s Guide

Contents

Main 2E253-49R SmartSwitch 2200 Installation Users Guide ETHERNET WORKGROUP SWITCH 2E253-49R 37482536 Page i Only qualied personnel should perform installation procedures. NOTICE FCC NOTICE VCCI NOTICE INDUSTRY CANADA NOTICE iii CABLETRON SYSTEMS, INC. iv v CABLETRON SYSTEMS SALES AND SERVICE, INC. vi vii CABLETRON SYSTEMS LIMITED viii ix DECLARATION OF CONFORMITY Page xi Contents NETWORK REQUIREMENTS INTRODUCTION ABOUT THIS GUIDE 3 B A 4 Figures Page About This Guide Important Notice STRUCTURE OF THIS GUIDE USING THIS GUIDE RELATED DOCUMENTS Management Users Guide http://www.cabletron.com/ DOCUMENT CONVENTIONS Page Introduction 1-1 Introduction 48 Ports (10 Mbps) HSIM/VHSIM Slot 2E253-49R 2600-01 1.1.1 Connectivity 1.1.2 Full Duplex Switched Ethernet 1.1.3 Standard/Full Duplex Auto-Negotiation 1.1.4 Runtime IP Address Discovery 1.1.5 SmartTrunk 1.1.6 Remote Monitoring (RMON) 1.1.7 Broadcast Suppression 1.1.8 Port/VLAN Redirect Functions 1.1.9 Trafc Rate Limiting 1.1.10 Flow Control 1.1.11 GARP Switch Operation 1.1.12 802.1 Port Priority 1.1.13 Management 1.1.14 Switching Options Page 1.2 GETTING HELP Network Requirements 2.1 SmartTrunk 2.2 10BASE-T NETWORK Page Installation 3.1 UNPACKING THE DEVICE 3.2 INSTALLING OPTIONS 3.3 INSTALLING THE DEVICE 3.3.1 Tabletop or Shelf Installation 3-4 Installation 2600-02 Figure 3-1 Tabletop or Shelf Installation 3.3.2 Rackmount Installation A = 15 cm (6 in) B = 57 cm (22.5 in) C = 53 cm (21 in) C B A D D = 213 cm (7 ft) ETHERNET WORKGROUP SWITCH 132412 1 Strain-Relief Bracket Strain-Relief Bracket Screws COM 3-6 Installation 2504-04 Rackmount Bracket CPU PWR 132412 1 37482536 3.3.3 Connecting Power NOTE The two power supplies in the 2E253-49R have automatic voltage sensing that allows connection to power sources ranging from 100125 Vac, 2.5 A or 200240 Vac, 1.25 A, 50/60 Hz. NOTE If the power-up sequence is interrupted on this device, or if optional hardware has been Screws 19-Inch Rack 3.4 CONNECTING TO THE NETWORK Primary Redundant AC outlets are on separate circuits Connecting to the Network Installation 3-9 RJ21 Angle Adapter COM 2E253-49R 3.5 COMPLETING THE INSTALLATION Troubleshooting 4-1 Troubleshooting 2E253-49R CPU PWR 2600-09 Figure 4-1 LANVIEW LEDs Page Page Page 4.2 TROUBLESHOOTING CHECKLIST Page Using the RESET Button Troubleshooting 4-7 4.3 USING THE RESET BUTTON The RESET button shown in Figure 4-2 resets and re-initializes the 2E253-49R. RESET Button Page A Specications A.2 PHYSICAL PROPERTIES A.1 DEVICE SPECIFICATIONS Page A.6 COM PORT PINOUT ASSIGNMENTS A.7 REGULATORY COMPLIANCE Page B Optional Installations and Mode Switch Bank Settings B.1 REQUIRED TOOLS Removing the Chassis Cover B-2 Optional Installations and Mode Switch Bank Settings B.2 REMOVING THE CHASSIS COVER This section describes how to remove the 2E253-49R chassis cover. Page Page B.3 SETTING THE MODE SWITCHES B.4 SIMM UPGRADE SIMM Upgrade Optional Installations and Mode Switch Bank Settings B-7 B.4.1 Locating SIMMs Figure B-3 shows the location of the DRAM SIMM connector. B.4.2 Installing the DRAM SIMM Installing Optional HSIM or VHSIM Interface Modules Optional Installations and Mode Switch Bank Settings B-9 B.5 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULES Connectors Optional HSIM or VHSIM Page Index Index Index-2 M N P R S