Menus and Indications Screen Viewfinder 4 Chapter

Viewfinder Normal Indications

Only when connecting the DSR-1/1P

Indication

Meaning

 

 

50P CONNECT

Connection with the PRO 50-pin

 

connector on the DSR-1/1P.

 

(Freeze mix function is disabled.)

 

 

MP TAPE

An incorrect type of cassette has

 

been loaded. (The cassette is

 

automatically ejected and the

 

indication disappears in about two

 

seconds.)

 

 

CLIP DATA ERR

Abnormality of the cassette memory

 

data.

 

 

AUDIO 48kHz?

At back space editing, audio

(4 flashes/s)

recording mode has changed from

 

32 kHz mode (4-channel mode) to

 

48 kHz mode (2-channel mode).

 

 

AUDIO 32kHz?

At back space editing, audio

(4 flashes/s)

recording mode has changed from

 

48 kHz mode (2-channel mode) to

 

32 kHz mode (4-channel mode).

 

 

ERROR:91-13F

Failure in loading or saving the

 

cassette memory data.

 

When other error indication

 

appears, refer to the operating

 

instructions for the DSR-1/1P.

CLIP CONT?

Asking whether you will continue

 

shooting in ClipLink mode or not

 

when the cassette contains ClipLink

 

data. (The indication disappears

 

when you press the ClipLink

 

CONTINUE button on the DSR-1/

 

1P or start the next shooting without

 

pressing it.)

 

 

CLIP NEAR END

At back space editing in ClipLink

 

mode, capacity for only 1 to 3 index

 

pictures remains.

 

 

CLIP END

Impossible to record any more clip

 

shots.

 

 

qf White balance indication The following indications appear.

Indication

Meaning

 

 

EZ

Operating in EZ mode (The ATW function is

 

selected.)

 

 

ATW

The ATW function is selected. (The ATW

 

button was pressed and the indicator is lit.)

 

 

W:A

White balance memory A is selected.

 

 

W:B

White balance memory B is selected.

 

 

W:P

Preset white balance is selected.

 

 

W:M

Manual adjustment is performed remotely.

 

 

qg SKIN DTL indication

This appears when the skin detail function is activated (The SKIN DTL switch is set ON.)

qh EVS indication

This appears when the EVS (Enhanced Vertical definition System) function is enabled. (See page 84.)

qj Lens f-stop indication

This shows the f-stop of the lens.

Note

Depending on the lens being used, this indication may differ slightly from the actual f-stop on the lens.

qk Gain indication

This shows the gain value, and the settings of the HYPER GAIN switch and the DPR (Dual Pixel Readout) function (see page 64) as shown in the following table.

Example indication

Meaning

 

 

18dB

Gain setting is 18 dB.

 

 

DPR 18dB

The DPR function is enabled.

 

In this case the DPR function

 

approximately doubles the gain (an

 

increase of 6 dB) over the current

 

gain setting (in this case 18 dB).

 

 

HYPER

The HYPER GAIN switch is in the

 

ON position.

 

In this case the hyper gain function

 

increases the gain by a factor of

 

about 60 or 120 with respect to 0

 

dB regardless of the current gain

 

setting (that is, increased to 36 or

 

42 dB).

 

 

ql Filter setting indication

This shows the setting of the FILTER control.

Indication

Filter setting

 

 

 

3200

1

(3200K)

 

 

 

 

56ND

2

(5600K

+ 1/8ND)

5600

3

(5600K)

 

 

 

 

56ND

4

(5600K

+ 1/64ND)

w; Clock indication

The clock indication is shown in one of the following ways (according to the CLOCK IND setting of CAM, BARS, or OFF in advanced menu page 8).

CAM: Always displayed.

BARS: Displayed whenever color bars are displayed.

OFF: Not displayed.

If the clock indication is displayed during recording, it is recorded onto the image.

56 Chapter 4 Viewfinder Screen Indications and Menus