Manuals / Canon / Computer Equipment / Projector

Canon LV-7260, LV-7265, LV-X7 user manual Using On-Screen Menu, ❶ Using the Menus

Models: LV-X7 LV-7265 LV-7260

1 82

Download 82 pages 9.47 Kb

Page 48

Image 48

5. Using On-Screen Menu

❶Using the Menus

NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.

1. Press the MENU button on the remote control or projector cabinet to display the Menu.

POWER INFO.

IMAGE INPUT AUTO PC

ASPECT

NO SHOW

BACK

2.Press the SELECT or button on the remote control or the projector cabinet to highlight the menu for the item you want to adjust or set.

POWER INFO.

IMAGE INPUT AUTO PC

ASPECT

NO SHOW

BACK

3.Press the SELECT button or the OK button on the remote control or the projector cabinet to select a submenu or item.

POWER INFO.

IMAGE INPUT AUTO PC

ASPECT

NO SHOW

BACK

Page 48

Image 48

Canon LV-7260, LV-7265, LV-X7 user manual Using On-Screen Menu, ❶ Using the Menus

Contents

LV-7265/LV-7260/LV-X7 MULTIMEDIA PROJECTORUser’s Manual EnglishSafety Cautions Important InformationPrecautions Machine Noise Information Regulation - 3. GPSGVImportant Information Federal Communication Commission Notice Canadian Radio Interference RegulationsRéglementation canadienne sur les intérferences radio LAMP HANDLING PRECAUTIONS Lamp ReplacementIF A LAMP EXPLODES DISPOSAL OF WASTE LAMPImportant Safeguards InstallationFire and Shock Precautions Important InformationDo not use any power cords than the supplied one Important InformationUse Caution When Carrying or Transporting the Projector Remote Control PrecautionsImportant Information CARRYING/TRANSPORTING THE PROJECTOR Table of Contents viii Table of Contents6. Maintenance 7. Appendix1. Introduction ❶ Whats in the Box?AC power cord Remote control❷ Introduction to the Projector Features youll enjoy1. Introduction Congratulations on Your Purchase of The Projector1. Introduction About this users manual ❸ Part Names of the Projector Adjustable Tilt Foot Lock Button See pageAdjustable Tilt Foot See page Lens Main Power Switch1. Introduction Bottom To turn the logo upside down, follow the steps below1. Push one end of the logo gently 3. Release your hold and turn the logo upside downTop Features 1. POWER Button2. POWER Indicator 3. WARNING IndicatorTerminal Panel Features 7 8 6. VIDEO IN Connector RCA7. S-VIDEO IN Connector Mini DIN 4 Pin 9. SERVICE PORT Mini DIN 8 Pin❹ Part Names of the Remote Control 11122. POWER Button Detecting the Signal Automatically1. Introduction 17. D. ZOOM + - Button18. FREEZE Button 12. BACK ButtonBattery Installation Remote Control PrecautionsOperating Range for Wireless Remote Control 1. Introduction2. Installation and Connections ❶ Setting Up the Screen and the Projector 2. Installation and Connections200 128 300 1902. Installation and Connections Selecting a Location LV-7260/LV-X7 Throw Distance and Screen Size2. Installation and Connections Reflecting the Image❷ Making Connections 2. Installation and ConnectionsConnecting Your PC or Macintosh Computer LV-7265 Enabling the computer’s external display2. Installation and Connections Using Two Analog COMPUTER Inputs Simultaneously LV-7265SERVICE PORT DIGITAL IN2. Installation and Connections When Viewing a DVI Digital Signal LV-72652. Installation and Connections Connecting Your PC or Macintosh Computer LV-7260/LV-X72. Installation and Connections Connecting an External Monitor The LV-7260 and LV-X7 do not have the AUDIO OUT connectorLV-7265 NOTE Daisy chain connection is not possible2. Installation and Connections Connecting Your DVD Player with Component OutputUse audio equipment for stereo sound 2. Installation and Connections Connecting Your VCR or Laser Disc PlayerS-VIDEO IN AUDIO IN2. Installation and Connections Connecting the Supplied Power Cord 3. Projecting an Image Basic Operation ❶ Turning on the Projector3. Press the POWER button on the projector cabinet or the POWER button on the remote control for about3. Projecting an Image Basic Operation Note on Startup screen Menu Language Select screenTo select a menu language, follow these steps 2. Press the OK button to execute the selection❷ Selecting a Source Detecting the Signal AutomaticallySelecting Default Source 1. Select Setup → Options → Default source select from the menu❸ Adjusting the Picture Size and Position Adjust the Tilt Foot5. The rear foot height can be adjusted up to 10 mm/0.4 inch 3. Projecting an Image Basic OperationUse the ZOOM lever to fi nely adjust the im- age size on the screen 3. Projecting an Image Basic Operation ZoomFocus Use the FOCUS ring to obtain the best focus❹ Correcting Keystone Distortion Adjusting with buttons on the cabinetAdjusting with the Remote Control 3. Projecting an Image Basic OperationAdjusting with the Auto Keystone Function LV-7265 only 3. Projecting an Image Basic Operation1. Press the MENU button The menu will be displayed 3. Press the SELECT button❻ Turning Up or Down Volume ❺ Automatically Optimizing on RGB ImageAdjusting the Image Using Auto PC adjustment 3. Projecting an Image Basic Operation❼ Turning off the Projector 2. Press the OK button or press the POWERbutton again3. Turn off the Main Power switch. The power indicator will go out 3. Projecting an Image Basic Operation❽ After Use 1. Unplug the power cord 2. Disconnect any other cables3. Retract adjustable tilt feet if extended 5. Put the projector and its accessories in the supplied soft case4. Convenient Features ❶ Turning off the Image and Sound❷ Freezing a Picture ❸ Enlarging and Moving a Picture❹ Using the Remote Mouse Receiver LV-7265/LV-7260 4. Convenient FeaturesConnecting the remote mouse receiver to your computer When operating a computer via the remote mouse receiver4. Convenient Features Operating your computer’s mouse from the remote controlYou can operate your computers mouse from the remote control About Drag Mode❺ Preventing the Unauthorized Use of the Projector 4. Convenient FeaturesTo enable the Password function 3. Use the SELECT or button to select Installation4. Convenient Features To turn on the projector when Password is enabledTo disable the Password function 1. Press the Main Power Switch to the On position4. Convenient Features The password confirmation screen will be displayed6. Type in your password and press the OK button 5. Use the SELECT or button to select off and press the OK button5. Using On-Screen Menu ❶ Using the Menus5. Using On-Screen Menu 5. Adjusting the level of a selected item or selecting an itemFor Adjusting items Slide bar For Selecting items Solid triangle❷ Menu Elements 5. Using On-Screen Menu❸ List of Menu Items 5. Using On-Screen MenuImage adjustment Display settings5. Using On-Screen Menu ResetInformation ❹ Menu Descriptions & Functions Image adjustment 5. Using On-Screen MenuDetail settings Selecting Reference Setting Reference Adjusting Color Temperature Color temperature❺ Menu Descriptions & Functions Display settings 5. Using On-Screen MenuAdjusting White Balance White balance Reset5. Using On-Screen Menu Copyright❻ Menu Descriptions & Functions Setup 5. Using On-Screen MenuCorrecting Vertical Keystone Distortion Manually Keystone adjustment General5. Using On-Screen Menu Enabling Key Sound and Error Sound BeepSelecting Lamp Mode Lamp mode Selecting Menu Language Language5. Using On-Screen Menu Installation Selecting Projector Orientation Image flip H/VSelecting Communication Speed Communication speed Disabling the Cabinet Buttons Key lock5. Using On-Screen Menu Enabling Password PasswordSelecting a Color for Background No signal screen Setting Off Timer Off timer5. Using On-Screen Menu Selecting Default Source Default source selectEnabling Fan Speed Mode Fan mode Auto5. Using On-Screen Menu Input signal select Selecting Signal FormatLV-7265 ❼ Menu Descriptions & Functions Information 5. Using On-Screen MenuInput signal Replacement lamp❽ Menu Descriptions & Functions Reset 5. Using On-Screen Menu VersionResetting settings and adjustments Reset Clearing Lamp Hour Meter Lamp counter6. Maintenance ❶ Cleaning or Replacing the FilterTo clean the air-filter To replace the filter sponge❷ Cleaning the Cabinet and the Lens 6. Maintenance3. Reinstall the new filter cover 4. Turn on the projector 5. Reset the Filter counter. See page❸ Replacing the Lamp 6. MaintenanceTo replace the lamp 6. Maintenance 2. Remove the lamp cover3. Remove the lamp 6. Maintenance 4. Insert a new lamp until the lamp is plugged into the socketSecure it in place with the two screws Be sure to tighten the screws 5. Reattach the lamp cover❶ Troubleshooting 7. AppendixIndicator Messages Over-Temperature ProtectionProblem 7. AppendixCheck These Items For more information contact your dealer7. Appendix If there is no picture, or the picture is not displayed correctly❷ Speciﬁcations Model NumberLV-7265/LV-7260/LV-X7 7. AppendixMechanical The specifi cations are subject to change without notice7. Appendix LV-7260/LV-X7 1W monaural❸ Cabinet Dimensions SERVICE PORT7. Appendix LV-7265❹ Pin Assignments of D-Sub ANALOG Input Connector Mini D-Sub 15 Pin ConnectorSignal Level Video signal 0.7Vp-p Analog Sync signal TTL level Only ANALOG-1 input connector supported on LV-7265❺ Compatible Input Signal List 7. Appendix❻ Relationship between Screen Size and Projection distance 7. AppendixLV-7265 7. Appendix LV-7260/LV-X7❼ PC Control Codes and Cable Connection SERVICE PORT Mini DIN-8P7. Appendix PC Control Codes❽ Troubleshooting Check List Power7. Appendix Video and AudioIn the space below please describe your problem in detail Installation environmentSignal cable 7. AppendixCANON U. S. A., INC