Single Duct Air Terminal Zone Controller
VAV Fan Terminal Zone Controller
Secondary Terminal Zone Controller
Installation, Start-Up and
Configuration Instructions
Part Numbers 33ZCFANTRM, 33ZCVAVTRM, 33ZCSECTRM
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Zone Controller Hardware . . . . . . . . . . . . . . . . . . . . . . . . 2
•SPACE TEMPERATURE SENSOR
•PRIMARY AIR TEMPERATURE SENSOR
•SUPPLY AIR TEMPERATURE (SAT) SENSOR
•RELATIVE HUMIDITY SENSOR
•INDOOR AIR QUALITY (CO2) SENSOR
Mount Zone Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
•LOCATION
•MOUNTING
Connect the Power Transformer . . . . . . . . . . . . . . . . . . 7
Connect Airflow Pickups . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
•SPACE TEMPERATURE SENSOR INSTALLATION
•PRIMARY AIR TEMPERATURE SENSOR INSTALLATION
•SUPPLY AIR TEMPERATURE (SAT) SENSOR INSTALLATION
•INDOOR AIR QUALITY SENSOR INSTALLATION
•HUMIDITY SENSOR
Remote Occupancy Contact. . . . . . . . . . . . . . . . . . . . . 26
Connect the Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Modulating Baseboard Hydronic Heating . . . . . . . . 26
Connect the CCN Communication Bus . . . . . . . . . . 26
•COMMUNICATION BUS WIRE SPECIFICATIONS
•CONNECTION TO THE COMMUNICATION BUS
Perform System
Network Addressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Initial Operation and Test. . . . . . . . . . . . . . . . . . . . . . . . 30
Airflow Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Fan and Heat Configuration and Test. . . . . . . . . . . . 30
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Points Display Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Modify Controller Configuration. . . . . . . . . . . . . . . . . 32
•ALARM LIMIT CONFIGURATION SCREEN
•CONTROLLER IDENTIFICATION SCREEN
•HOLIDAY CONFIGURATION SCREENS
•LINKAGE COORDINATOR CONFIGURATION SCREEN
•OCCUPANCY CONFIGURATION SCREEN
•SET POINT SCREEN
Service Configuration Selection Screen. . . . . . . . . 37
•AIRFLOW SERVICE CONFIGURATION SCREEN
•TERMINAL SERVICE CONFIGURATION SCREEN
•OPTIONS SERVICE CONFIGURATION SCREEN
•SECONDARY DAMPER SERVICE
CONFIGURATION SCREEN
Maintenance Table Menu Screen . . . . . . . . . . . . . . . . 43
•LINKAGE MAINTENANCE TABLE
•OCCUPANCY MAINTENANCE TABLE
•ZONE AIR BALANCE/COMMISSIONING TABLE
•ZONE MAINTENANCE TABLE
SAFETY CONSIDERATIONS
SAFETY NOTE
Good judgement should be used in applying any manu- facturer’s instructions to avoid injury to personnel or dam- age to equipment and property.
Disconnect all power to the unit before performing mainte- nance or service. Unit may automatically start if power is not disconnected. Electrical shock and personal injury could result.
If it is necessary to remove and dispose of mercury contac- tors in electric heat section, follow all local, state, and fed- eral laws regarding disposal of equipment containing hazardous materials.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book | 1 | 4 | PC 111 | Catalog No. | Printed in U.S.A. | Form | Pg 1 | 303 | Replaces: New | |
Tab | 11a | 13a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|