Carrier 48SS018-060 Ð Slab Mounting Details, Ð Suggested Rigging for Units Without, Base Rail

Fig. 11 Ð Slab Mounting Details

NOTICE TO RIGGERS

Hook rigging shackles through holes in lifting brackets, as shown in Detail ``A.'' Lifting brackets to be centered around the unit center of gravity. Use wooden top skid when rigging, to prevent rigging straps from damaging unit.

All panels must be in place when rigging.

UNIT	MAX		A			B		C
48SS	WEIGHT
Size	lb	kg	in.	mm	in.		mm	in.	mm
018	332	150			24.3		618	24.85	631
024	375	170			22.4		570	24.85	631
030	384	174			22.3		565	24.85	631
036	408	185	49.4	1255	22.0		559	24.85	631
042	447	203			22.5		571	28.85	733
048	486	220			21.0		533	34.85	885
060	525	238			21.5		545	34.85	885
UNIT
48SX
024	405	184			22.8		579	28.9	733
030	408	185			22.4		569	28.9	733
036	438	199	49.4	1255	22.4		569	28.9	733
042	463	210			22.8		579	34.9	885
048	494	224			21.1		536	34.9	885
060	525	238			21.5		545	34.9	885

Fig. 12 Ð Suggested Rigging for Units Without

Base Rail

NOTICE TO RIGGERS

Hook rigging shackles through holes in lifting brackets, as shown in Detail ``A.'' Lifting brackets to be centered around the unit center of gravity. Use wood top skid when rigging, to prevent rigging straps from damaging unit. Remove 4 screws to slide wood support through rectangular hole in rail.

All panels must be in place when rigging.

UNIT	MAX		A			B			C
48SS	WEIGHT
Size	lb	kg	in.	mm	in.		mm	in.		mm
018	320	145			24.4		619	28.2		715
024	363	165			22.6		574	28.2		715
030	380	172			22.5		571	28.2		715
036	396	180	49.4	1255	22.2		563	28.2		715
042	435	197			22.6		574	32.2		816
048	474	215			21.2		538	38.2		969
060	513	233			21.6		549	38.2		969
UNIT
48SX
024	393	178			22.9		582	32.2		816
030	396	180			22.6		574	32.2		816
036	426	193	49.4	1255	22.5		571	32.2		816
042	451	205			22.9		582	38.2		969
048	482	219			21.3		540	38.2		969
060	513	233			21.6		549	38.2		969

Fig. 13 Ð Suggested Rigging for Units With

Optional Base Rail

UNITS WITHOUT BASE RAIL Ð If accessory rigging brackets are to be used for rigging, install them as follows:

Secure screws and paint protectors solidly against unit basepan to hold lifting brackets in position.

Never use lifting brackets when the temperature is be- low −10 F.

Never exceed 200 lbs per bracket of lifting force.

Never use lifting brackets for lifting other models of air- conditioning units.

Lifting point should be directly over the unit center of gravity.

1.Position brackets as close to the corners of unit as pos- sible. Be sure brackets are well outside of center of grav- ity. (See Fig. 2, 4, 6, 8, and 12.).

2.Position paint protectors and foam strips between screws and painted surface of unit. Tighten screws until they make contact with the paint protectors.

3.Secure device or hook of sufficient strength to hole in bracket as shown in detail ``A'' of Fig. 12.

4.If wood top is available, use it for a spreader bar to pre- vent straps from damaging unit. If wood top is not avail- able, use spreader bars of sufficient length.

12