MAIN BURNERS (48MP Only) Ð At the beginning of each heating season, inspect for deterioration or blockage due to corrosion or other causes. Observe the main burner ¯ames. Refer to Main Burners section on page 52.

FLUE GAS PASSAGEWAYS (48MP Only) Ð The ¯ue col- lector box and heat exchanger cells may be inspected by re- moving heat exchanger access panel (Fig. 3 and 4), ¯ue box cover, and main burner assembly (Fig. 52). Refer to Main Burners section on page 52 for burner removal sequence. If cleaning is required, remove heat exchanger baffles and clean tubes with a wire brush.

Use caution with ceramic heat exchanger baffles. When installing retaining clip, be sure the center leg of the clip extends inward toward baffle. See Fig. 53.

COMBUSTION-AIR BLOWERS (48MP Only) Ð Clean pe- riodically to assure proper air¯ow and heating efficiency. In- spect blower wheel every fall and periodically during heat- ing season. For the ®rst heating season, inspect blower wheel bi-monthly to determine proper cleaning frequency.

To inspect blower wheel, remove heat exchanger access panel. Shine a ¯ashlight into opening to inspect wheel. If cleaning is required, remove motor and wheel assembly by removing screws holding motor mounting plate to top of com- bustion fan housing (Fig. 54). The motor and wheel assem- bly will slide up and out of the fan housing. Remove the blower wheel from the motor shaft and clean with a deter- gent or solvent. Replace motor and wheel assembly.

Lubrication

COMPRESSORS Ð Each compressor is correctly charged at the factory. Refer to 06E Compressor Service Manuals if additional information regarding compressor lubrication sys- tem is required. See Compressor Oil section on page 29 and Table 3.

FAN SHAFT BEARINGS Ð Lubricate fan shaft bearings at least once a year with suitable bearing grease. Extended grease lines are provided on pulley side of blower. Typical lubri- cants are given below:

MANUFACTURER

LUBRICANT

Texaco

Regal AFB-2*

Mobil

Mobilplex EP No. 1

Sunoco

Prestige 42

Texaco

Multifak 2

*Preferred lubricant because it contains rust and oxidation inhibitors.

FAN MOTOR BEARINGS Ð The condenser- and evaporator- fan motors have sealed bearings so no ®eld lubrication is required.

DOOR HINGES Ð All door hinges should be lubricated at least once a year.

Coil Cleaning Ð Clean the coils with a vacuum cleaner, compressed air, water, or a non-wire bristle brush.

Refrigerant Circuit

LEAK TESTING Ð Units are shipped with a full operating charge of R-22 (see Table 1). If there is no pressure in the system, introduce enough nitrogen to search for the leak. Repair the leak using good refrigeration practices. After leaks are repaired, system must be evacuated and dehydrated using methods described in GTAC II, Module 4, System Dehydration.

REFRIGERANT CHARGE (Refer to Table 1) Ð At the liq- uid line connection point on each circuit is a factory- installed liquid line service valve. On each valve is a 1¤4-in. Schrader connection for charging liquid refrigerant.

All units are shipped with a complete operating charge of R-22. See unit nameplate and Table 1 for amount of charge. When adding a complete charge, evacuate system using stand- ard evacuating procedures and weigh in the speci®ed amount of charge. All units have charging charts for each refrigerant circuit. See Fig. 55-59.

Fig. 52 Ð Burner Section Detail

CERAMIC

BAFFLE

CLIP

HEAT EXCHANGER

TUBES

NOTE: One baffle and clip wll be in each upper tube of the heat exchanger.

Fig. 53 Ð Removing Heat Exchanger Ceramic

Baffles and Clips

Fig. 54 Ð Combustion Blower Removal

47

Page 47
Image 47
Carrier 48MPD, MPE62L-10R, 50MP62L-10R specifications Lubrication, Refrigerant Circuit, Manufacturer Lubricant

MPE62L-10R, 50MP62L-10R, 48MPD specifications

The Carrier 48MPD, 50MP62L-10R, and MPE62L-10R are advanced rooftop packaged units designed for a variety of commercial HVAC applications. These systems offer a compelling blend of energy efficiency, versatility, and high performance, making them ideal choices for businesses looking to enhance their indoor climate control.

One of the standout features of the Carrier 48MPD series is its high efficiency rating, which significantly reduces operational costs while minimizing environmental impact. The unit utilizes advanced scroll compressors that provide reliable and efficient cooling capabilities, ensuring optimal temperature regulation regardless of outdoor conditions. This innovative design also contributes to quieter operation, enhancing indoor comfort without disruptive noise levels.

The Carrier 50MP62L-10R model boasts superior cooling and heating capabilities, equipped with a multi-speed fan system that allows for tailored airflow to suit specific project requirements. This model's economizer feature is pivotal for harnessing outside air to offset mechanical cooling, leading to further energy savings, particularly in moderate weather conditions. Additionally, the unit's dual-fuel capability enhances its operational flexibility, allowing it to switch between electric and gas heating sources depending on efficiency needs.

In terms of control technologies, the MPE62L-10R is equipped with Carrier's advanced Smart Evaporator Control, which ensures precise humidity management while optimizing energy consumption. This model also integrates seamlessly with building automation systems, enabling remote monitoring and adjustments for greater operational oversight and efficiency. The intuitive user interface simplifies system programming and operation, making it accessible even for those without extensive technical backgrounds.

Another important characteristic of these units is their robust construction, designed to withstand challenging weather conditions and ensure longevity. The use of high-quality materials and components means lower maintenance costs over time.

Overall, the Carrier 48MPD, 50MP62L-10R, and MPE62L-10R represent a well-engineered suite of HVAC solutions that excel in efficiency, adaptability, and user-friendliness, establishing themselves as leading choices for commercial indoor climate management. With their blend of innovative technology and solid performance, these systems are well-suited to meet the diverse needs of modern commercial spaces.