Using the Mixer

 

 

 

 

 

 

 

 

 

 

 

3. Use the R-17 (t, y) buttons to move the thick

Mixer Operation

 

 

brackets (%) to the parameter you want to

 

 

 

 

 

 

 

 

 

 

 

change.

 

To change mixer parameters

 

 

• The parameters that can be configured depend on the

 

 

 

 

 

 

 

 

 

 

 

 

currently selected setting. For details, refer to the

1. Press the C-5 (MIXER) button.

 

 

 

 

 

 

sections shown in the table below.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When this setting is

These parameters can be

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

selected:

configured:

 

 

 

 

 

 

 

 

 

 

 

MASTER

MASTER parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(page E-42)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• This causes the mixer screen to appear.

 

 

MIC/INST

MIC/INST parameters

 

 

 

 

 

 

 

(page E-43)

 

 

 

 

 

 

 

 

Currently selected setting

 

 

DSP

 

 

 

DSP parameters (page E-42)

(MASTER, DSP, MIC/INST, or A01 to A16/B01 to B16)

 

 

 

 

 

 

 

 

 

A01 to A16/B01 to B16

Part parameters (page E-44)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• When you move the thick brackets (%) to one of the

 

 

 

 

 

 

 

 

 

 

 

 

setting values of a part parameter, all of the part

 

 

 

 

 

 

 

 

 

 

 

 

parameter values of the group (A or B) to which the part

 

 

 

 

 

 

 

 

 

 

 

 

belongs are indicated by level meter black boxes.

 

 

 

 

 

 

 

 

 

 

 

Parameter/Setting value

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Currently selected setting part

 

 

 

 

 

 

 

 

 

(when currently selected setting is A01 to A16/B01 to B16)

 

 

 

 

 

 

 

2. Use the R-17 (u, i) buttons to select the

 

 

4. Use the dial or R-14 (–, +) buttons to change the

 

mixer parameter you want to change.

 

 

 

 

 

setting value.

 

 

• You can select master (MASTER), effect (DSP),

 

 

 

 

 

 

•

Pressing the R-14(–, +) buttons at the same time

 

 

microphone input (MIC/INST), or a part (A01 through

 

 

 

 

 

 

 

returns a parameter to its initial default setting.

 

 

A16, B01 through B16). The currently selected setting

 

 

 

 

 

 

 

•

While the “Part” (part on/off) setting of a part parameter

 

 

is shown in the line two of the display.

 

 

 

 

 

 

 

is being configured, pressing both of the R-14(–, +)

 

• While a part is selected, you can toggle between

 

 

 

 

 

 

 

buttons at the same time will change the setting to “Sol”

 

 

Group A and Group B by pressing both of the R-17 (u,

 

 

 

 

 

 

 

 

(Solo). For details, see “Part Parameters” (page E-44).

 

 

i) buttons at the same time.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5. Repeat steps 2 through 4 as required to

 

 

 

 

 

 

 

 

 

 

 

configure other parameters.

 

 

 

 

 

 

 

 

 

 

 

6. To exit the mixer, press the C-5 (MIXER) button

 

 

 

 

 

 

 

 

 

 

 

or the R-15 (EXIT) button.

 

 

 

 

 

 

 

 

 

 

 

•

This exits the mixer screen.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• While master (MASTER), effect (DSP) or microphone input (MIC/INST) is selected in step 2 above, setting, you also can perform normal keyboard play (play using layer, split, and Auto Accompaniment).

• While an individual part (A01 through A16, B01 through B16) is selected in step 2 above, pressing a keyboard key will sound only notes of the selected part. All other types of performance operations (layer, split, Auto Accompaniment, etc.) are disabled.

E-40