Selecting and Playing a Tone 
5. Press the (LAYER) button so its lamp is lit.
IMPORTANT!
• You can select a tone for each zone in both the |
| Lit |
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
MASTER CONTROL and CARD PLAYER modes. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Note however that some procedures and operations |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
(lamp lighting status) when a tone is selected for |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
each zone in the CARD PLAYER mode are different |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
from those in the case of the MASTER CONTROL |
|
|
|
|
|
|
| Unlit | Lit | |||||||
mode. | • At this time the (UPPER 1) button lamp will go out | |||||||||||||||
Here, explanations are based on selecting a tone for | ||||||||||||||||
and the (UPPER 2) button lamp will light in its | ||||||||||||||||
each zone in the MASTER CONTROL mode. For | ||||||||||||||||
place. This indicates you can select the UPPER 2 zone | ||||||||||||||||
information about selecting tones in the CARD | tone. |
|
|
| ||||||||||||
PLAYER mode, see “To select a tone for each zone | 6. Select the UPPER 2 zone tone. |
|
|
| ||||||||||||
in the CARD PLAYER mode” (page |
|
|
| |||||||||||||
NOTE | 7. Play something on the keyboard to check | |||||||||||||||
• When using Layer and/or Split to play more than | how the tones sound layered together. | |||||||||||||||
one tone at the same time, you can adjust the volume | • At any time you can press the (UPPER 1) button to | |||||||||||||||
balance of each zone, perform octave shift for each | ||||||||||||||||
change the UPPER 1 zone tone or the (UPPER 2) | ||||||||||||||||
zone, and configure detailed settings for the effects | ||||||||||||||||
button to change the UPPER 2 zone tone. | ||||||||||||||||
applied to zones. For details about parameters that | 8. To cancel tone layering, press the | |||||||||||||||
can be configured and setting procedures, see | ||||||||||||||||
“Editing Zone Parameters” (page | (LAYER) button again so its lamp goes out. | |||||||||||||||
Layering Two Tones
UPPER 1
UPPER 2
1. Use the “Tone List” (page
2. Check to make sure that the both the (LAYER) and (SPLIT) button lamps are unlit.
•If one or both lamps are lit, press the (LAYER) and (SPLIT) buttons to turn them off.
3.Press the (UPPER 1) button so its lamp is lit.
•This indicates you can select the UPPER 1 zone tone.
Lit
4. Select the UPPER 1 zone tone.
•For details about selecting tones, see “To select a tone” (page
English