Wall-Mounting | Cisco Systems Cisco ME 3400 specs

Chapter 2 Switch Installation

Installing the Switch

After the switch is mounted in the rack, you need to do these tasks to complete the installation:

•Power on the switch. See the “Verifying Switch Operation” section on page 2-5.

•Connect to the RJ-45 connector of a dual-purpose port and run the Initial Configuration Dialog. See the Cisco ME 3400 and ME 2400 Ethernet Access Switches Getting Started Guide for instructions.

•Connect to the front-panel ports. See the “Connecting to the 10/100 and 10/100/1000 Ports” section on page 2-20and the “Connecting to SFP Modules” section on page 2-21to complete the installation.

•We recommend attaching the cable guide to prevent the cables from obscuring the front panel of the switch and the other devices installed in the rack. Use the supplied black screw shown in Figure 2-8to attach the cable guide to the left or right bracket.

For configuration instructions about using the CLI setup program, go to Appendix D, “Configuring the Switch with the CLI-Based Setup Program.”

Wall-Mounting

To install the switch on a wall, follow the instructions in these procedures:

•Attaching the Brackets to the Switch for Wall-Mounting, page 2-14

•Mounting the Switch on a Wall, page 2-15

Attaching the Brackets to the Switch for Wall-Mounting

Figure 2-10shows how to attach a 19-inch bracket to one side of the switch. Follow the same steps to attach the second bracket to the opposite side.

Figure 2-10 Attaching the 19-inch Brackets for Wall-Mounting

Cisco
ME
	2400	SERIES
1
2

1Phillips flat-head screws

132690

1

Cisco ME 3400 Ethernet Access Switch Hardware Installation Guide

2-14	OL-7677-04

Image 38

Cisco Systems Cisco ME 3400 manual Attaching the Brackets to the Switch for Wall-Mounting, Phillips flat-head screws

Contents

Americas Headquarters Page N T E N T S Installing and Removing SFP Modules Speed, Duplex, and Autonegotiation IP Settings D-2 Organization AudiencePurpose Conventions Related Publications OL-7677-04 Setting up the Switch Switch Models 1describes the switch models Front Panel Description Cisco ME 3400-24TS AC and DC Switches Front Panel Cisco ME 3400-24TS AC Ethernet Access Switch Front Panel Cisco ME 3400-24FS Switch AC Switch Front Panel Cisco ME 3400G-12CS AC and DC Switches Front Panel Cisco ME 3400G-2CS Switch Front Panel System LED Dual-purpose ports Console port SFP module ports 10/100 Ports Only the Cisco ME-3400-24TS Switches SFP Module Ports SFP Modules System LED LEDsSFP Module Patch Cable These illustrations show the location of the System LED Console Power Supply LEDs Only Cisco ME 3400G-12CS Switches Port LEDs Console Port Dual-Purpose Port LEDs Cable lock Ground connector Fan exhaust Cisco ME 3400-24TS Switch Rear PanelCisco ME 3400-24FS Switch Rear Panel Exhaust fan Cable lock Ground connector Cisco ME 3400-2CS Switch Rear Panel Power Supply FeaturesCisco ME 3400G-12S Switch Rear Panel Fan exhaust AC power connector Ground connector Network Configurations Cisco ME AC Switch Power SupplyCisco ME DC Switch Power Supply Management Options Preparing for Installation This section covers these topics Switch Installation Preparing for Installation 122F 50C Statement Cisco ME 3400G-12CS Switches Installation GuidelinesCisco ME 3400-24TS Switches Powering Off the Switch Verifying Switch OperationInstalling the Switch This section describes these installation procedures Removing Screws from the Switch Rack-Mounting Attaching Brackets to the Switch Rack-Mounting Brackets Attaching Brackets to 19-Inch Racks 191022 Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks Attaching Brackets for Etsi Racks Mounting the Switch in a Rack Phillips machine screws Cable guide and screw Phillips flat-head screws Attaching the Brackets to the Switch for Wall-MountingWall-Mounting Mounting the Switch on a Wall 11 Mounting the Switch on a Wall Installing and Removing SFP Modules Table- or Shelf-Mounting Installing SFP Modules 12 SFP Module with a Bale-Clasp Latch Removing SFP Modules Bale clasp Inserting and Removing the SFP Module Patch Cable Connecting to the 10/100 and 10/100/1000 Ports 17 Connecting to an Ethernet Port LC connector Connecting to SFP ModulesConnecting to Fiber-Optic SFP Modules Connecting to 1000BASE-T SFP Modules 19 Connecting to a 1000BASE-T SFP Module Connecting to Dual-Purpose Ports 20 Connecting to a Dual-Purpose Port Where to Go Next This section includes these troubleshooting topics Diagnosing ProblemsCheck Switch Post Results Bad or Damaged Cable Check Switch LEDsCheck Switch Connections Ethernet and Fiber Cables Ping the End Device SFP Module Port IssuesPort and Interface Settings Spanning Tree Loops Speed, Duplex, and Autonegotiation How to Clear the Switch IP Address and ConfigurationCheck Switch Performance Autonegotiation and NIC Cards Locating the Switch Serial Number Serial Number Location on the Cisco ME 3400G-2CS Switch Serial Number Location on the Cisco ME 3400G-2CS Switch 10/100 Ports Connector SpecificationsThese sections describe the connectors used with the switch Figure A-1 10/100 Port Pinouts Figure A-2 Fiber-Optic SFP Module LC Connector Dual-Purpose Ports Cable and Adapter Specifications SFP Module Cable Specifications Two Twisted-Pair Cable Pinouts Identifying a Crossover Cable Four Twisted-Pair Cable Pinouts for 1000BASE-T PortsCrossover Cable and Adapter Pinouts RxD TxD Adapter PinoutsTxD RxD Switch Console RJ-45-to-DB-25 Port DTE Technical Specifications This appendix lists the switch technical specifications AC Power Requirements Physical Dimensions OL-7677-04 Connecting to DC Power Review these safety warnings before you ground the switch Grounding the SwitchPreparing the Ground Wire Figure C-1 Stripping the Ground Wire Torque to 15 lbf-in Figure C-3 Torquing Ground-Lug Screws Telco rack Connecting the Grounding Wire to Earth GroundTelco rack Grounding wire Wiring the DC-Input Power Source Primary power feed Secondary redundant power feed All Cisco ME 3400 Switches Cisco ME 3400-24TS SwitchesCisco ME 3400G-12CS Switches Figure C-8 Terminal Block Plug Console Figure C-11 Inserting Wires in the Terminal Block Plug Figure C-13 Completed Wiring of Terminal Block Plug OL-7677-04 Accessing the CLI Through the Console Port Starting the Terminal-Emulation Software Completing the Setup Program Entering the Initial Configuration InformationIP Settings Enter a virtual terminal Telnet password, and press Return Enter an enable secret password, and press ReturnEnter an enable password, and press Return Switch or as a standalone switch These choices appear Auto-MDIX Pinouts See also connectors and cables cautions Numerics Connection procedures Cisco IOS command-line interface CiscoViewConnecting outside the building warning Connectors and cables 10/100 ports Console port Installing SFP modules 2-17 to IN-3 Power on LEDs Running at power on Power Connecting to ACConnecting to DC Connectors Ground connection IN-5 IN-6