Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems IE301024TC 2-19, 15 Wall-Mounting the Cisco IE-3010-16S-8PC, Switch2500Series

Models: 3010 IE3010 IE301024TC

1 100

Download 100 pages 7.97 Kb

Page 41

Image 41

Figure 2-15 Wall-Mounting the Cisco IE-3010-16S-8PC

Chapter 2 Switch Installation

Installing the Switch

Figure 2-15 Wall-Mounting the Cisco IE-3010-16S-8PC

Switch2500Series	CiscoConnected Grid
	207557

After the switch is mounted on the wall:

•Wire the switch to a power source. See Chapter 3, “Power Supply Installation.”

•For configuration instructions about using the CLI setup program, go to Appendix C, “Configuring the Switch with the CLI Setup Program.”

•Connect the switch ports. See the “Connecting Devices to the Ethernet Ports” section on page 2-25.

Cisco IE 3010 Switch Hardware Installation Guide

	78-19581-02	2-19

Page 41

Image 41

Cisco Systems IE301024TC manual 2-19, 15 Wall-Mounting the Cisco IE-3010-16S-8PC, Switch2500Series, CiscoConnected Grid

Contents

Cisco Systems, Inc 170 West Tasman Drive San Jose, CA Revised October 12800 553-NETS Fax 408 Cisco IE 3010 Switch Hardware Installation GuideReorient or relocate the receiving antenna Alarm Input Alarm PortsSwitch Models Alarm LEDsWall-Mounting WarningsPower-Supply Module Specifications A-4 TroubleshootingAlarm Port Switch LEDsEntering the Initial Configuration Information C-7 IP Settings C-7 Accessing the CLI Through the Console Port C-1Completing the Setup Program C-7 Uninstalling the Cisco Microsoft Windows Vista USB Driver C-6Preface Cisco IE 3010 Switch Getting Started Guide Release Notes for the Cisco IE 3010 SwitchCisco IE 3010 Switch Software Configuration Guide Cisco IE 3010 Switch Command ReferenceSwitch Models, page Cable Side, page Power-Supply Side, page Switch ModelsProduct Overview C H A P T E RCable Side Figure 1-2 Cisco IE-3010-16S-8PC Cable-Side View 10/100 Fast Ethernet PortsPoE Ports Dual-Purpose Ports SFP Modules SFP Module Patch Cable Power-Input TerminalAlarm Ports Management Ports Alarm InputAlarm Output LEDs Switch Panel LEDsAlarm LEDs Power-Supply Module LEDsSystem LED Power-Supply Module LEDsPort LEDs Console LEDs1-10 RJ-45 and USB Console Port LEDsPoE LED SD Flash Memory CardDual-Purpose Port LEDs SD Flash Memory Card LED1-12 Power-Supply SideSwitch LEDs Power-Supply Side LEDs1-13 Network Configurations Power Supply FeaturesManagement Options 1-14Warnings, page Installation Guidelines, page Switch InstallationVerifying Switch Operation, page Installing the Switch, page Installing and Removing SFP Modules, page1.75 in. 4.4 cm. Statement Verifying Switch Operation Installation GuidelinesRack-Mounting the Switch, page Installing the SwitchRack-Mounting Rack-Mounting, page Wall-Mounting, pageChapter 2 Switch Installation Installing the Switch Attaching Brackets for 19-Inch RacksCisco IE 3010 Switch Hardware Installation Guide Figure 2-1 Attaching Brackets for 19-Inch RacksFigure 2-2 Attaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch Racks for IP-30 Compliance OptionalRubber plug Switch Cisco IE 3010 Switch Hardware Installation Guide Chapter 2 Switch Installation Installing the SwitchFigure 2-4 Inserting the Rubber Plugs 78-19581-02Cisco IE 3010 Switch Hardware Installation Guide Chapter 2 Switch Installation Installing the SwitchFigure 2-5 Inserting the Rubber Plugs 78-19581-02Chapter 2 Switch Installation Installing the Switch 2-10Cisco IE 3010 Switch Hardware Installation Guide Figure 2-6 Attaching Brackets for 19-Inch RacksCisco CGS 2-11Figure 2-7 Attaching Brackets for 19-Inch Racks Figure 2-8 Attaching 23-Inch Brackets Attaching Brackets for 23-Inch Racks2-12 Figure 2-9 Attaching Brackets for ETSI Racks Attaching Brackets for ETSI Racks2-13 Rack-Mounting Rack-Mounting the Switch2-14 Wall-Mounting Wall-Mounting the Switch, pageAttaching Brackets, page Attaching Brackets for IP-30 Compliance Optional, page2-16 Attaching BracketsAttaching Brackets for IP-30 Compliance Optional Figure 2-12 Inserting the Rubber Plugs in the Switch Holes 2-17Chapter 2 Switch Installation Installing the Switch Cisco IE 3010 Switch Hardware Installation Guide2-18 Wall-Mounting the SwitchSwitch2500Series 2-19Figure 2-15 Wall-Mounting the Cisco IE-3010-16S-8PC CiscoConnected Grid2-20 Installing and Removing SFP ModulesInstalling SFP Modules 2-21 Inserting and Removing the SFP Module Patch CableRemoving SFP Modules 2-22 Removing the SFP Module Patch CableFigure 2-19 Connecting Two Switches with an SFP Module Patch Cable Figure 2-18 Inserting an SFP Module Patch Cable2-23 Replacing the SD Flash Memory CardFigure 2-20 Loosening the Captive Screw Figure 2-21 Removing the SD Slot CoverStep 6 Place the SD slot cover tabs into the hinge 2-24Connecting to the 10/100 and 10/100/1000 Ports Connecting Devices to the Ethernet PortsConnecting to the 10/100 and 10/100/1000 Ports, page Connecting to the 10/100 PoE Ports, pagehttp//tools.cisco.com/cpc/launch.jsp Connecting to the 10/100 PoE Ports2-26 Device2-27 Where to Go NextChapter 2 Switch Installation Where to Go Next Cisco IE 3010 Switch Hardware Installation GuideChapter 2 Switch Installation Where to Go Next 2-28Cisco IE 3010 Switch Hardware Installation Guide 78-19581-02Power-Supply Modules Power Supply InstallationPower-Supply Modules, page Installation Guidelines, page Grounding the Switch, pageFigure 3-2 PWR-RGD-LOW-DC/IA Power-Supply Module Figure 3-1 PWR-RGD-AC-DC/IA Power-Supply ModuleChapter 3 Power Supply Installation Power-Supply Modules Cisco IE 3010 Switch Hardware Installation GuideInstallation Guidelines Power-Supply Module InstallationInstallation Guidelines, page Installing a Power-Supply Module, page Wiring the Power Source, page Removing the Power-Supply Module, pageEquipment That You Need Installing a Power-Supply ModuleGrounding the Switch Wire lead Figure 3-3 Stripping the Ground Wire0.5 in. 12.7 mm ± 0.02 in. 0.5 mm InsulationInstalling the Power-Supply Module in the Switch Wiring the Power Source AC 5 A, DC 15 A Statement 100-240V~, 50-60Hz, 2A Power-Input Terminal100-240V~, 50-60Hz, 2A 10A 10AStep 7 To connect the AC power 3-10Figure 3-13 Connecting the Wires to the High-Voltage AC Power PSU1 3-11Figure 3-14 Connecting the Wires to the Low-Voltage DC Power PSU2 Cisco IEStep 9 AC power Removing the Power-Supply ModuleDC power Warning Hot surface. StatementStep 5 Install a new power-supply module or a blank cover 3-13Chapter 3 Power Supply Installation Removing the Power-Supply Module 3-14Cisco IE 3010 Switch Hardware Installation Guide 78-19581-02Diagnosing Problems TroubleshootingSwitch POST Results Diagnosing Problems, pageSwitch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber-Optic Cables10/100 and 10/100/1000 Port Connections Interface Settings10/100 PoE Port Connections SFP ModuleSpanning Tree Loops Switch PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsFinding the Switch Serial Number Resetting the Switch to the Factory Default SettingsChapter 4 Troubleshooting Finding the Switch Serial Number Figure 4-2 Serial Number Location for the Power-Supply ModulesCisco IE 3010 Switch Hardware Installation Guide 78-19581-02Switch Specifications Technical SpecificationsSwitch Specifications Power-Supply Module Specifications Alarm RatingsPower Requirements Table A-3 Technical Specifications for the Cisco IE-3010-24TC SwitchPower-Supply Module Specifications Alarm Input and Output Ratings Alarm RatingsAlarm Ratings Appendix A Technical Specifications Alarm Ratings78-19581-02 Appendix A Technical Specifications Alarm RatingsCisco IE 3010 Switch Hardware Installation Guide Connector Specifications Connector and Cable SpecificationsConnector Specifications, page B-1 Cables and Adapters, page B-4 10/100, page B-1 SFP Module Connectors, page B-2SFP Module Connectors Figure B-4 Alarm Port Pinouts Alarm PortDual-Purpose Ports Figure B-3 10/100/1000 Port PinoutsSFP Module Cables Cables and AdaptersSFP Module Cables, page B-4 Cable Pinouts, page B-6 Console Port Adapter Pinouts, page B-7Page Switch 1 TP0+ 2 TP0 3 TP1+ 6 TP1 4 TP2+ 5 TP2 7 TP3+ 8 TP3 Cable PinoutsTwo Twisted-Pair Straight-Through Cable Schematic for 10/100 Ports Two Twisted-Pair Crossover Cable Schematic for 10/100 PortsConsole Port Adapter Pinouts Table B-3 Console Port Signaling Using a DB-25 Adapter Accessing the CLI Through the Console Port Configuring the Switch with the CLI Setup ProgramRJ-45 Console Port A P P E N D I X CFigure C-1 Connecting the Console Cable USB Console Port Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB DriversUninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Using the Add or Remove Programs UtilityUsing the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB DriverCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Page Page Appendix C Configuring the Switch with the CLI Setup Program C-10Entering the Initial Configuration Information Cisco IE 3010 Switch Hardware Installation GuideNumerics I N D EIN-1 IN-2 IN-3 IN-4 Cisco IE 3010 Switch Hardware Installation Guide IN-5two-poled disconnect device wall-mounting Index78-19581-02 IN-6Index Cisco IE 3010 Switch Hardware Installation Guide