Cisco Systems OL-17037-01 Using the CLI to Configure Country Codes, show country supported, 7-52

Chapter 7 Controlling Lightweight Access Points

Configuring Country Codes

Using the CLI to Configure Country Codes

Follow these steps to configure country codes using the CLI.

Step 1 To see a list of all available country codes, enter this command:

show country supported

Step 2 Enter these commands to disable the 802.11a and 802.11b/g networks:

config 802.11a disable network

config 802.11b disable network

Step 3 To configure the country codes for the countries where your access points are installed, enter this command:

config country code1[,code2,code3,...]

If you are entering more than one country code, separate each by a comma (for example, config country US,CA,MX). Information similar to the following appears:

Changing country code could reset channel configuration.

If running in RFM One-Time mode, reassign channels after this command.

Check customized APs for valid channel values after this command.

Are you sure you want to continue? (y/n) y

Step 4 Enter Y when prompted to confirm your decision. Information similar to the following appears:

Configured Country............................. Multiple Countries:US,CA,MX

Auto-RF for this country combination is limited to common channels and power.

KEY: * = Channel is		legal in this country and may be configured manually.
	A = Channel is	the Auto-RF default in this country.
	. = Channel is	not legal in this country.
	C = Channel has been configured for use by Auto-RF.
	x = Channel is	available to be	configured for use by Auto-RF.
	(-) = Regulatory	Domains allowed	by this country.
------------	:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11BG	:
Channels	:	1 1 1 1 1

:1 2 3 4 5 6 7 8 9 0 1 2 3 4

------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

US (-AB)	: A * * * * A * * * * A .	.	.
CA (-AB)	: A * * * * A * * * * A .	.	.
MX (-NA)	: A * * * * A * * * * A .	.	.
Auto-RF	: C x x x x C x x x x C .	.	.
------------	:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11A	:	1	1	1	1	1	1	1	1	1	1 1	1	1	1	1	1
Channels	: 3 3 3 4 4 4 4 4 5 5 6 6 0		0	0	1	1	2	2	2	3	3 4	4	5	5	6	6
--More--	or (q)uit

:4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5

------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

US (-AB)		: . A . A . A . A A A A A * * * * * . . .	*	* *	A A A A *
CA	(-ABN)	: . A . A . A . A A A A A * * * * * . . .	*	* *	A A A A *
MX (-N)		: . A . A . A . A A A A A	.	. .	A A A A *
	Auto-RF : . C . C . C . C C C C C		.	. .	C C C C x

Step 5 To verify your country code configuration, enter this command:

show country

	Cisco Wireless LAN Controller Configuration Guide
7-52	OL-17037-01