Using the CLI to View Clients, Ap Mac | Cisco Systems OL-17037-01

Chapter 7 Controlling Lightweight Access Points

Viewing Clients

This page shows the following information:

•The general properties of the client

•The security settings of the client

•The QoS properties of the client

•Client statistics

•The properties of the access point to which the client is associated

Using the CLI to View Clients

Use these CLI commands to view client information.

•To see the clients associated to a specific access point, enter this command: show client ap {802.11a 802.11b} Cisco_AP

Information similar to the following appears:

MAC Address	AP	Id	Status	WLAN Id Authenticated
-----------------	------		-------------	---------	-------------
00:13:ce:cc:8e:b8	1		Associated	1	No

•To see a summary of the clients associated to the controller’s access points, enter this command: show client summary

Information similar to the following appears:

Number of Clients	................................			6
MAC Address	AP Name	Status		WLAN	Auth	Protocol Port Wired
-----------------	----------------- -------------			----	----	-------- ---- -----
00:13:ce:cc:8e:b8	Maria-1242	Probing		N/A	No	802.11a	1	No
00:40:96:a9:a0:a9	CJ-AP1	Probing		N/A	No	802.11a	1	No
00:40:96:ac:44:13	CJ-AP1	Probing		N/A	No	802.11a	1	No
00:40:96:b1:fe:06	CJ-AP1	Probing		N/A	No	802.11a	1	No
00:40:96:b1:fe:09	CJ-AP1	Probing	N/A	No	802.11a 1			No

•To see detailed information for a specific client, enter this command: show client detail client_mac

Information similar to the following appears:

			Client	MAC Address	00:40:96:b2:a3:44
			Client	Username	N/A
			AP MAC	Address	00:18:74:c7:c0:90
			Client	State	Associated
			Wireless LAN Id		1
			BSSID		00:18:74:c7:c0:9f
			Channel	..........................................	56
			IP Address		192.168.10.28
			Association Id		1
			Authentication Algorithm		Open System
			Reason	Code	0
			Status	Code	0
			Session Timeout		0
			Client	CCX version	5
			Client	E2E version	No E2E support
			Cisco Wireless LAN Controller Configuration Guide
			Cisco Wireless LAN Controller Configuration Guide

	7-78				OL-17037-01
	7-78				OL-17037-01

Image 78

Cisco Systems OL-17037-01 manual Using the CLI to View Clients, Ap Mac

Contents

Controlling Lightweight Access Points Access Point Communication Protocols Guidelines for Using CapwapController Discovery Process Page Verifying that Access Points Join the Controller Config network master-base enableConfig network master-base disable Configuring Global Credentials for Access Points Viewing Capwap MTU InformationDebugging Capwap Global Configuration All APs Details for Credentials Save config Show ap config general CiscoAPShow ap summary Configuring Authentication for Access Points Lwapp ap dot1x username username password password Using the GUI to Configure Authentication for Access Points Controller Cisco Wireless LAN Controller Configuration Guide Using the CLI to Configure Authentication for Access Points Config ap dot1xuser add username user password password all Config ap dot1xuser disable all CiscoAP AP Dot1x User Mode field shows Customized Embedded Access Points Configuring the Switch for Authentication Dns-server ipaddress Default-router ipaddress Ip dhcp pool poolname Autonomous Access Points Converted to Lightweight Mode Reverting from Lightweight Mode to Autonomous Mode Using a Controller to Return to a Previous Release Authorizing Access Points Authorizing Access Points Using SSCsAuthorizing Access Points Using MICs Authorizing Access Points Using LSCs Using the GUI to Configure LSC Config certificate lsc ca-cert add delete Config certificate lsc enable disableConfig certificate lsc ca-server http//urlport/path Config certificate lsc other-params keysize Config certificate lsc ap-provision auth-list add APmacaddr Config certificate lsc ap-provision revert-cert retriesShow certificate lsc summary Using the GUI to Authorize Access Points Show certificate lsc ap-provision Config auth-list add mic ssc lsc apmac apkey Using the CLI to Authorize Access PointsConfig auth-list ap-policy mic ssc lsc enable disable Show auth-list Using Dhcp Option 43 and Dhcp Option Troubleshooting the Access Point Join Process Controlling Lightweight Access Points Show ap config global Configuring the Syslog Server for Access PointsViewing Access Point Join Information Show ap join stats summary all Joined Converted Access Points Send Radio Core Dumps to Controller Debug ap enable disable command cmd CiscoAP Using the CLI to Retrieve Radio Core Dumps Using the GUI to Upload Radio Core DumpsShow ap crash-file Using the CLI to Upload Radio Core Dumps Transfer upload start Uploading Memory Core Dumps from Converted Access Points Using the GUI to Upload Access Point Core Dumps Display of MAC Addresses for Converted Access Points Using the CLI to Upload Access Point Core Dumps Supporting Oversized Access Point Images Config ap reset-button enable disable ap-nameall Cisco Workgroup Bridges WGB Example Guidelines for Using WGBs Configure terminal Sample WGB Configuration Using the GUI to View the Status of Workgroup BridgesShow dot11 association 11 Clients Detail 12 WGB Wired Clients Debug dhcp message enable Debug dhcp packet enable Using the CLI to View the Status of Workgroup BridgesUsing the CLI to Debug WGB Issues Debug dot11 mobile enable Debug dot11 state enable Configuring Backup Controllers Using the GUI to Configure Backup Controllers 14 Global Configuration 15 All APs Details for High Availability Using the CLI to Configure Backup Controllers Config advanced timers ap-discovery-timeout interval Config advanced timers auth-timeout interval Configuring Failover Priority for Access Points 1300 16 Global Configuration Using the CLI to View Failover Priority Settings Enabled Configuring Country Codes Guidelines for Configuring Multiple Country Codes Using the GUI to Configure Country Codes 19 All APs Details for Advanced Using the CLI to Configure Country Codes Show country supportedShow country Show country channels Config 802.11a enable network config 802.11b enable network Controlling Lightweight Access Points Guidelines for Migration Migrating Access Points to the -U Regulatory DomainConfig country J3 Show ap migrate Config ap migrate j52w52 all apname Using the W56 Band in Japan Dynamic Frequency Selection Optimizing Rfid Tracking on Access Points Using the GUI to Optimize Rfid Tracking on Access Points 20 802.11b/g/n Cisco APs Configure Using the CLI to Optimize Rfid Tracking on Access Points Config ap monitor-mode tracking-opt CiscoAPConfig 802.11b enable CiscoAP Config advanced probe limit numprobes interval Configuring Probe Request ForwardingConfig advanced probe filter enable disable Show ap monitor-mode summary Inventory Performing a Link Test 22 All APs Details for Inventory Using the GUI to Perform a Link Test Link Test Configuring Link Latency Using the CLI to Perform a Link Test Using the GUI to Configure Link Latency 25 All APs Details for Advanced Using the CLI to Configure Link Latency Config ap link-latency enable disable CiscoAP all Configuring Power over Ethernet Config ap link-latency reset CiscoAP Using the GUI to Configure Power over Ethernet EPoE Power EPoE Mode 15.4 W Optimized 20 W Cisco Wireless LAN Controller Configuration Guide Using the CLI to Configure Power over Ethernet Config ap power injector enable CiscoAP all installedConfig ap power injector enable CiscoAP all override Debug ap command led flash seconds CiscoAP Configuring Flashing LEDsUsing the GUI to View Clients Viewing Clients Controlling Lightweight Access Points Viewing Clients 28 Search Clients 29 Clients Detail Using the CLI to View Clients AP MAC S69 OL-17037-01