Cobalt Networks 9084 3-16

39084 Function Submenu List and Descriptions

3-16 9084 PRODUCT MANUAL 9084-OM (V4.0)

(continued)

•Color Gain Adjusts gain percentage (saturation)

applied to Chroma (C-channel).

(0% to 200% range in 0.1% steps; unity = 100%)

•Color Phase Adjusts phase angle applied to Chroma.

(-360° to 360° range in 0.1° steps; null = 0°)

•Gang Luma and Color Gain When set to On, changing either the Luma Gain or Color Gain controls

increases or decreases both the luma and chroma levels by equal

amounts.

•Black Hard Clip Applies black hard clip (limiting) at specified percentage.

(-6.8% to 50.0%; null = -6.8%)

Table 3-2 9084 Function Submenu List — continued

123

Proc Sat (sat

value) Color gain in percent

Vid Card Edge Control Menu:

123

Proc Phas (phase

value) Color phase angle applied in

degrees

Vid

Card Edge Control Menu:

123

Proc Gang On Ganging On

Off Ganging Off

Vid Card Edge Control Menu:

1234

Proc Clip BHCL (value) Clip value in percent;

0.1% precision

Vid Card Edge Control Menu:

Contents

Main Product Manual Copyright Disclaimer Trademark Information Table of Contents Page Chapter 1 1 9084 Card Software Versions and this Manual Introduction Manual Conventions E201 Warnings, Cautions, and Notes Warnings Cautions 1 Labeling Symbol Definitions Safety Summary Warnings Cautions ! WARNING ! Introduction 9084 Functional Description 9084 Input/Outputs 1-6 Color Corrector Figure 1-1 9084 Functional Block Diagram Video Processor Introduction Color Corrector Video Processor Frame Sync Function AFD Inserter User Control Interface Figure 1-2 9084 User Control Interface Introduction 9084 Rear I/O Modules Video Formats Supported by the 9084 Introduction Technical Specifications 1 Introduction 1 Warranty and Service Information Cobalt Digital Inc. Limited Warranty Introduction Contact Cobalt Digital Inc. Page Chapter 2 Installing the 9084 Into a Frame Slot 2 Installation and Setup Installing a Rear I/O Module 2 Setting Up 9084 Network Remote Control 1 2 Chapter 3 Control and Display Descriptions Function Submenu/Parameter Submenu Overview 9084 Card Edge Controls, Indicators, and Display Figure 3-2 shows and describes the 9084 card edge controls, indicators, and display. Figure 3-2 9084 Controls, Indicators, and Display Item Function 9084 Card Edge Control Menu/Submenu Structure Figure 3-3 Card Edge Controls Setup of Example Color Correction Function 12 34 Submenu Depth Vid A B C D E F G H I 3-6 D i s p Disp DashBoard User Interface 3-8 Figure 3-5 DashBoard Setup of Example Color Correction Function Cobalt Remote Control Panel User Interfaces 3 Accessing the 9084 Card via Remote Control Accessing the 9084 Card Using DashBoard Operating Instructions Accessing the 9084 Card Using a Cobalt Remote Control Panel Press the Select Device key and select a card as shown in the example below. 3 Checking 9084 Card Information Operating Instructions Ancillary Data Line Number Locations and Ranges Item Default Line No. / Range SD HD 9084 Function Submenu List and Descriptions Table 3-2 9084 Function Submenu List Provides the following Video Proc parametric controls. Video Proc 3-16 Page 3-18 Allows assignment of AFD (Active Format Description) codes to the SDI output video. Color Correction 3-20 Page 3-22 Provides video Frame Sync and delay control tools. (continued) Minimum Latency Frames Control 3-24 (continued) Reset Framesync Page 3-26 Color and Video Correction Examples Using the 9084 On-Set Monitor Color Correction Example Page Page 3-30 Figure 3-12 Applying Correction to Example Monitor Waveform Signal Miscellaneous Color and Video Correction Examples 3-32 Condition Observed On Waveform Monitor Correction Using 9084 Troubleshooting Error and Failure Indicator Overview 9084 Card Edge Status/Error Indicators and Display Figure 3-13 9084 Card Edge Status Indicators and Display Item Function 3-36 DashBoard Status/Error Indicators and Displays Figure 3-14 DashBoard Status Indicator Icons and Display Indicator Icon or Display Error Description Figure 3-15 Selecting Specific Cards for Card Info Status Display 3-38 Basic Troubleshooting Checks Item Checks 9084 Processing Error Troubleshooting Symptom Error/Condition Corrective Action Troubleshooting Network/Remote Control Errors In Case of Problems