TOP Right Hand Screw Dust Trap Cover, Clips | Craftsman 113.225900

14.Remove the top right hand screw which VOU installed in step 6 and loosen the other t_ree screws.

15.Install the Dust Trap cover and reD,ace me too right hand screw. Tighten ag five screws.

TOP RIGHT HAND SCREW

DUST TRAP COVER

iNSTALLING MOTOR, V-BELT,AND BELT GUARD

1.Locatethe following parts:

OTY. Description

1 Motor

1"L" Bracket

1Pulley (approx. 2" Dia.)

1V-Belt

4Carriage Bolt 5/16-18 x 3/4

4Flat Washer 5/16 I.D.

4Lockwasher 5/16 I.D.

4Hex Nut 5/16-18

Guard Assembly including a guard support, guard support bracket, self-threading screws, and clips.

2.Place motor against the motor mounting bracket and insert bolts through holes in motor base and then through holes marked "X" in motor mounting bracket. DO NOT TIGHTEN BOLTS AT THIS TIME. The "'L" bracket which holds the guard support must be slid between the motor base and the motor mounting bracket so motor must be loosely assembled to bracket at this time.

3.Slide long leg of "L" bracket between motor base and motor mounting bracket. Then sandwich the "L" bracket between the guard support bracket and the guard support and fasten together with self-threading screws as shown. Install clips onto belt guard support.

4.Install the 2" pulley onto the motor shaft flush with the end of the shaft and tighten the set screw in the pulley hub against the flat part of the motor shaft.

II

LOCKWASHER

CARRIAGE BOLT

5/t6-18 x 3/4

/

MOTOR

TWO HOLES

TOGETHER

CLIPS

10-32 X 1/2 IN,

BELT GUARD

SUPPORT BRACKET

SELF-THREADING'

SCREW

SUPPORT

/_ BELT GUARD

11

Image 11

Craftsman 113.225900, 113.225931, 113.225909 manual TOP Right Hand Screw Dust Trap Cover, TWO Holes, Clips, 10-32 X 1/2

Contents

Legs and Motor Belt and Disc Power tools General safety instructions Sander Before Using the SanderBefore Each USE At a time Whenever Sander is RunningPlan your work Grounded /n Ul OUTLETs Connecting to Power Source OutletProperly Unpacking and checking Contents Following parts are included with Model AssernbJyHAROWABEFORMOUNTINGTOOL& Motor Catalog no Mounting Belt and Disc Sander on Craftsman Steel LEG SET Belt Table Locking Installing Sanding Disc and Dust TrapAssembly Wrench Trap AssemblyFlat Spot Disc Dust Trap Flat Head Screws 10-32 X 1/2 TOP Right Hand Screw Dust Trap CoverTWO Holes Clips Place the bolt onto the motor pulley by rotating the pulley AssemblyON-OFF Switch Insert key into switch Find plastic cable hanger from among the loose parts Power Cord Motor CordCable Belt Locking Screw Installing Work TableDirectional ARROW\ Be LT Adjusting SCR EWS Pull Wrenches in this Direction to Apply Tension Pulley Installing Belt Dust TrapBelt Leftmoving To Right Belt Locking Screw Drive ANY Aojustm Ents Installing BackstopAssembWy Getting to know your belt and disc sander From Disc Positioning Lock Screw Stop Tilt Lock NUT Belt Adjusting Screw ONE on Each Side Lock NUt Raise the table and loosen the lock nut using a 7/16 wrenchGe ng to know you r belt and disc sander Place. It is locked uing the 1/2 wrench Before Each USE Before Using the SanderBasic operation END Finishing on Abrasive Belt Surface Finishing on Abrasive BeltBefore freeing any jammed material For finishing long pieces, remove the backstop Curved Edges CAT. no Motor Maintenance LubricationSears Recommends Following Accessories Causing thebelt to sli Too Motor wd! notBox Protector Open, only LOW Voltage Trouble Shooting -- MotorRemedy Hardware for Mounting Tool & Motor Parts ListSupplied With Craftsman Belt and Disc Sander Model no .225900 & 113,225931 47222 Housing, Disc With Plug Repair partsKey Part Description Outlet Before Proceeding Black Wire to Terminal T1 Green Wire to Green Screw Does Not Include Key No, 3. Order Separately If Required Repair partsSwitch Mounting Page BEL T and Disc Sander