Repair parts, Switch Mounting | Craftsman 113.225931, 113.225909

repair parts

_ _i _

CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.225900 & 113.225931

S 6

FIGURE 4 PARTS LIST

ON\OFF POWER OUTLET 60382 AND

		MOUNTING	BRACKET
Key
No.	No,		Description
J
--	60382	• Oa/Off	Power	Outlet
1	60375	Cord,	Molded
2	60378	Heusing, Switch
3	9-22255	t-Key, Switch
4	60374	t-Key, Switch
4	60374	Switch,	Locking
5	60376	Cever,	Switch
6	448007	Screw,	Pan Hd. No. 6 x 3/4
7	68066	Bracket,	Switch	Mounting
		Bracket,	Switch	Mounting

8STD600803 *Screw, Pan Hd. Plastite No. 8 x 3&/8

*Standard Hardware item - May be Purchased Locally.

•Does Not Include Key No, 3. Order Separately If Required.

TStock Item--May be secured through the Hardware Deeartment of most Sears Retail Stores or Catatog Order Houses.

NOTE: Shipping and handling charges for standard hardware items (identified by *l such as nuts. screws, washers, etc., make

buying these items by mait uCeconomicaL To avoid shipping and handling charges, you may obtain most of these locally

Page 30

Image 30

Craftsman 113.225931, 113.225909 Repair parts, Switch Mounting, Does Not Include Key No, 3. Order Separately If Required

Contents

Belt and Disc Legs and Motor General safety instructions Power tools Before Using the Sander Before Each USESander Whenever Sander is Running Plan your workAt a time Connecting to Power Source Outlet ProperlyGrounded /n Ul OUTLETs Contents Unpacking and checking AssernbJy HAROWABEFORMOUNTINGTOOL& MotorFollowing parts are included with Model Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog no Wrench Installing Sanding Disc and Dust TrapAssembly Belt Table Locking Disc Dust Trap Flat Head Screws AssemblyFlat Spot Trap Clips TOP Right Hand Screw Dust Trap CoverTWO Holes 10-32 X 1/2 Insert key into switch AssemblyON-OFF Switch Place the bolt onto the motor pulley by rotating the pulley Power Cord Motor Cord CableFind plastic cable hanger from among the loose parts Pull Wrenches in this Direction to Apply Tension Installing Work TableDirectional ARROW\ Be LT Adjusting SCR EWS Belt Locking Screw Belt Locking Screw Drive Installing Belt Dust TrapBelt Leftmoving To Right Pulley Getting to know your belt and disc sander Installing BackstopAssembWy ANY Aojustm Ents Belt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUT Place. It is locked uing the 1/2 wrench Raise the table and loosen the lock nut using a 7/16 wrenchGe ng to know you r belt and disc sander Lock NUt Before Using the Sander Basic operationBefore Each USE For finishing long pieces, remove the backstop Surface Finishing on Abrasive BeltBefore freeing any jammed material END Finishing on Abrasive Belt Curved Edges Causing thebelt to sli Motor Maintenance LubricationSears Recommends Following Accessories CAT. no Protector Open, only Motor wd! notBox Too Trouble Shooting -- Motor RemedyLOW Voltage Parts List Supplied WithHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222 Repair parts Key Part DescriptionWith Plug Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before Proceeding Repair parts Switch MountingDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander

Craftsman 113.225931, 113.225909, 113.225900 manual Repair parts, Switch Mounting

Models: 113.225900 113.225909 113.225931

repair parts

CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.225900 & 113.225931

FIGURE 4 PARTS LIST

ON\OFF POWER OUTLET 60382 AND

MOUNTING

BRACKET

Switch

Mounting

•Does Not Include Key No, 3. Order Separately If Required.