Craftsman Belt and Disc Sander Model 113 Parts & Diagrams

repair parts

CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.2259OO & 113.225931

4 3

			FIGURE
		SUPPLIED	WITH
Key	Part
No.	No.	Description
1	62614	Leg
2	;0314	1- Screw,TrussHd. 1/4-20 x 5/8

3STD541025 t* Nut, Hex1/4-20

4TD551225 1* Lockwasher,1/4 External

	68060	Channel,Support
	68060	Stiffener, Side
	68059	Stiffener, Side
7	62615	Stiffener, End
8	168061	Support,Motor
9	_TD541050 1* Nut, Hex1/2-13
10	803835	1- Foot, Leveling

--68062 1- Bagof LooseParts(Not illustrated)

1 PARTS LIST

MODEL 113.225931 ONLY

Key	Part
No.	No.	Description

HARDWARE FOR MOUNTING TOOL & MOTOR

STD523125 t'Screw, Hex Hd. 5/16-18 x 2-1/2

STD551131 _*Lockwasber, External 5/1B

STD541231 t'Nut, Hex Jam 5/16 x 18

STD551031 1*Washer, 11/32 x 11/16 x t/16

STD532507 1"*Bolt. Carriage5/16-18 x 3/4

tThese items all contained in LooseParts Bag,PartNo. _8062.

*StandardHardwareItem - May be PurchasedLeeelly.

Page 25

Image 25

Craftsman 113.225909, 113.225931, 113.225900 manual Supplied With, Parts List, Hardware for Mounting Tool & Motor

Contents

Legs and Motor Belt and Disc Power tools General safety instructions Before Each USE Before Using the SanderSander Plan your work Whenever Sander is RunningAt a time Properly Connecting to Power Source OutletGrounded /n Ul OUTLETs Unpacking and checking Contents HAROWABEFORMOUNTINGTOOL& Motor AssernbJyFollowing parts are included with Model Catalog no Mounting Belt and Disc Sander on Craftsman Steel LEG SET Assembly Installing Sanding Disc and Dust TrapWrench Belt Table Locking Flat Spot AssemblyDisc Dust Trap Flat Head Screws Trap TWO Holes TOP Right Hand Screw Dust Trap CoverClips 10-32 X 1/2 ON-OFF Switch AssemblyInsert key into switch Place the bolt onto the motor pulley by rotating the pulley Cable Power Cord Motor CordFind plastic cable hanger from among the loose parts Directional ARROW\ Be LT Adjusting SCR EWS Installing Work TablePull Wrenches in this Direction to Apply Tension Belt Locking Screw Belt Leftmoving To Right Installing Belt Dust TrapBelt Locking Screw Drive Pulley AssembWy Installing BackstopGetting to know your belt and disc sander ANY Aojustm Ents From Disc Positioning Lock Screw Stop Tilt Lock NUT Belt Adjusting Screw ONE on Each Side Ge ng to know you r belt and disc sander Raise the table and loosen the lock nut using a 7/16 wrenchPlace. It is locked uing the 1/2 wrench Lock NUt Basic operation Before Using the SanderBefore Each USE Before freeing any jammed material Surface Finishing on Abrasive BeltFor finishing long pieces, remove the backstop END Finishing on Abrasive Belt Curved Edges Sears Recommends Following Accessories Motor Maintenance LubricationCausing thebelt to sli CAT. no Box Motor wd! notProtector Open, only Too Remedy Trouble Shooting -- MotorLOW Voltage Supplied With Parts ListHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 47222 Housing, Disc Key Part Description Repair partsWith Plug Outlet Before Proceeding Black Wire to Terminal T1 Green Wire to Green Screw Switch Mounting Repair partsDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander

Craftsman Complete Guide to Belt Disc Sander Parts and Diagrams

Models: 113.225900 113.225909 113.225931