AssembWy, Installing Backstop | Craftsman 113.225909, 113.225931

assembWy

2. Attach the dust trap . make sure the top edge is below the surface of the abras ve be t

PAN HEAD SCREW

AND LOCKWASHER E3ELT DUST TRAP

BACKSTOPBACKSTOP

LOCK SCREW

INSTALLING BACKSTOP

1.Find one 5/16" x 1" Hex. Head bolt and one fiat washer among the loose parts.

2.Place the washer on the bolt. and screw it halfway into the mounting hole. Place the backstoo into pos- tion and tighten the bolt. When removing the bacK- stop, loosen the bolt but do not remove it,

getting to know your belt and disc sander

WARNING: FOR YOUR OWN SAFETY TURN
SWITCH "OFF" AND REMOVE PLUG FROM
POWER SOURCE OUTLET BEFORE	MAKING			BACK OF SANDER
ANY AOJUSTM ENTS.
		BACKSTOP	BELT	ADJUSTING
		BACKSTOP
			SCREW
LOCK	SCREW		(ONE	ON EACH SIDE)
\	\		(ONE	ON EACH SIDE)
\

WORK		/
TABLE	/	/
TABLE
			\
WORKTABLE	6 BELTTABLE	2 BELT_OC_'_G IDLER
TILT LOCK SCREW	STOP	SCREW	PULLEY
TILT LOCK SCREW	STOP	SCREW

(ONE ON EACH SIDE)

FRONT OFSANDER

Page 16

Image 16

Craftsman 113.225909 manual AssembWy, Getting to know your belt and disc sander, Installing Backstop, ANY Aojustm Ents

Contents

Belt and Disc Legs and Motor General safety instructions Power tools Before Each USE Before Using the SanderSander Plan your work Whenever Sander is RunningAt a time Properly Connecting to Power Source OutletGrounded /n Ul OUTLETs Contents Unpacking and checking HAROWABEFORMOUNTINGTOOL& Motor AssernbJyFollowing parts are included with Model Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog no Installing Sanding Disc and Dust Trap AssemblyWrench Belt Table Locking Assembly Flat SpotDisc Dust Trap Flat Head Screws Trap TOP Right Hand Screw Dust Trap Cover TWO HolesClips 10-32 X 1/2 Assembly ON-OFF SwitchInsert key into switch Place the bolt onto the motor pulley by rotating the pulley Cable Power Cord Motor CordFind plastic cable hanger from among the loose parts Installing Work Table Directional ARROW\ Be LT Adjusting SCR EWSPull Wrenches in this Direction to Apply Tension Belt Locking Screw Installing Belt Dust Trap Belt Leftmoving To RightBelt Locking Screw Drive Pulley Installing Backstop AssembWyGetting to know your belt and disc sander ANY Aojustm Ents Belt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUT Raise the table and loosen the lock nut using a 7/16 wrench Ge ng to know you r belt and disc sanderPlace. It is locked uing the 1/2 wrench Lock NUt Basic operation Before Using the SanderBefore Each USE Surface Finishing on Abrasive Belt Before freeing any jammed materialFor finishing long pieces, remove the backstop END Finishing on Abrasive Belt Curved Edges Motor Maintenance Lubrication Sears Recommends Following AccessoriesCausing thebelt to sli CAT. no Motor wd! not BoxProtector Open, only Too Remedy Trouble Shooting -- MotorLOW Voltage Supplied With Parts ListHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222 Key Part Description Repair partsWith Plug Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before Proceeding Switch Mounting Repair partsDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander

Craftsman 113.225909 AssembWy, Getting to know your belt and disc sander, Installing Backstop

Models: 113.225900 113.225909 113.225931

assembWy

INSTALLING BACKSTOP

getting to know your belt and disc sander

ANY AOJUSTM ENTS.

2 BELT_OC_'_G IDLER

FRONT OFSANDER