Assembly, ON-OFF Switch, Machine Pulley | Craftsman 113.225931

assembly

5.Place belt over machine pulley and insert the belt nl the open end of the guard and out the round opening.

MAKE SURE BELT HAS NOT SLIPPED OFF OF

MACHINE PULLEY FROM STEP 3, DISC AND

DUST TRAP INSTALLATION.

6.Place the bolt onto the motor pulley by rotating the pulley,

7.Move the motor sideways so that the belt is in the center of the opening in the top of the base. Visually line up the pulleys and V-belt.

8.PUSH downward on motor to apply tension to belt and tighten motor bolt nuts.

9.Check guard support before tightening guard support screws. Guard support must becentered around motor

shaft, Tighten screws.

10.Push guard into position on guard support.

/BELT

/

r•

I

IELT MUST BE ON

MACHINE PULLEY

/ /

/

ON-OFF SWITCH

WARNING: DON'T CONNECT POWER CORD TO

ELECTRICALOUTLET IN YOU R SHOP UNTIL YOU ARE

SURE MOTOR ROTATION IS CORRECT. SEE PAGE 5,

The On-Off Switch has a locking feature. THIS FEATURE IS INTENDED TO PREVENT UNAUTHORIZED AND POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS.

1. Insert key into switch,

_

NOTE: Key is made of yellow plastic

12

Image 12

Craftsman 113.225931 Assembly, ON-OFF Switch, Place the bolt onto the motor pulley by rotating the pulley, Machine Pulley

Contents

Belt and Disc Legs and Motor General safety instructions Power tools Before Using the Sander Before Each USESander Whenever Sander is Running Plan your workAt a time Connecting to Power Source Outlet ProperlyGrounded /n Ul OUTLETs Contents Unpacking and checking AssernbJy HAROWABEFORMOUNTINGTOOL& MotorFollowing parts are included with Model Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog no Installing Sanding Disc and Dust Trap AssemblyWrench Belt Table Locking Assembly Flat SpotDisc Dust Trap Flat Head Screws Trap TOP Right Hand Screw Dust Trap Cover TWO HolesClips 10-32 X 1/2 Assembly ON-OFF SwitchInsert key into switch Place the bolt onto the motor pulley by rotating the pulley Power Cord Motor Cord CableFind plastic cable hanger from among the loose parts Installing Work Table Directional ARROW\ Be LT Adjusting SCR EWSPull Wrenches in this Direction to Apply Tension Belt Locking Screw Installing Belt Dust Trap Belt Leftmoving To RightBelt Locking Screw Drive Pulley Installing Backstop AssembWyGetting to know your belt and disc sander ANY Aojustm Ents Belt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUT Raise the table and loosen the lock nut using a 7/16 wrench Ge ng to know you r belt and disc sanderPlace. It is locked uing the 1/2 wrench Lock NUt Before Using the Sander Basic operationBefore Each USE Surface Finishing on Abrasive Belt Before freeing any jammed materialFor finishing long pieces, remove the backstop END Finishing on Abrasive Belt Curved Edges Motor Maintenance Lubrication Sears Recommends Following AccessoriesCausing thebelt to sli CAT. no Motor wd! not BoxProtector Open, only Too Trouble Shooting -- Motor RemedyLOW Voltage Parts List Supplied WithHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222 Repair parts Key Part DescriptionWith Plug Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before Proceeding Repair parts Switch MountingDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander