Manuals / Brands / Power Tools / Sander / Craftsman / Power Tools / Sander

Craftsman 113.225900, 113.225909, 113.225931 manual sander

1 32

Download 32 pages, 2.03 Mb

"rge ng to know you belt and disc

fLoosen the table positioning lock screw., . posi-

tion the table approximately 1/16" awa_ from

the abrasive disc.

g. Tilt the table downward but don't tighten the ock

screw, and position it as close to the disc as pos-

sibte. Using the head of a combination square,

check the angle of the table with the disc,

h. If the table is not 45 ° with the disc:

sander

/

i. Raise the table and loosen the lock nut using a

7/16" wrench.

j, Screw the stop screw in or out, using a 3/8'"

wrench so that when the table touches it, it is 45 °

with the disc.

k. Tighten the lock nut.

WARNING: To avoid trapping the work or fingers

between the table and sanding surface, the table must

be repositioned on the rod to maintain amaxtmum

1/16 inch space between the table and sanding

surface,

STOP SCREW

4. BACKSTOP LOCK SCREW locks the backstop in

place. It is locked u_ing the 1/2"' wrench,

BACKSTOP

LOCK SCREW

\

BACKSTOP

5. BELT TABLE LOCKING BOLTS ... lock the

belttable in position.

To adjust to vertical position:

a. Remove the backstop.

b. Loosen the two belt table locking bolts using the

1/2" wrench supplied with your machine.

c. Position belt table vertically and tighten the two

bolts.

6, ABRASIVE BELT TABLE STOP can be adj-

usted so that the abrasive belt table is level with

the floor when in a horizontal position.

a, Loosen the lock nut using a 3/4"" wrench.

BELT TABLE

LOCKING BOLT/

b, Place a level on the abrasive belt table and using a

314" wrench, screw the stop bolt in or out until

the table is level.

LOCK NUt

STOP BOLT

18

Contents

Main Save This Manual For Future Reference MODEL NO. 113, 225909 MODEL NO. 113.225931 BEL T AND D/SC SANDER .assembly operating orepair parts Sold by SEARS, ROEBUCK AND CO., Chicago, iL. 60684 U.S.A. general safety instructions power tools safety instructions for beJt and disc sander BEFORE USING THE SANDER: WHEN INSTALLING OR MOVING THE SANDER. BEFORE EACH USE: CHECK DAMAGED PARTS. Check for: safety instructions for belt and disc sander Keep your face and booy to one side. out of line with a pos- sible throwback WHENEVER SANDER IS RUNNING. BEFORE LEAVING THE SANDER: electrical requirements CONNECTING TO POWER SOURCE OUTLET /Do l CHECK MOTOR ROTATION unpacking and checking [q_u O assernbJy F S,DE ST,FFEN R / \ oo WARNING: Never use gasoline, naptha, or similar highly volatile solvents. / INSTALLING SANDING DISC AND DUST TRAP assembly /ONSHAFT 9. Attach the Disc Dos1 Trap with four flat head screws !-" long. \ \ iNSTALLING MOTOR, V-BELT, BELT GUARD 1. Locatethefollowingparts: AND 11 II assembly / I // ON-OFF SWITCH 2. To turn machine on. insert finger INSTALLING WORK TABLE \ INSTALLING ABRASIVE BELT-TENSIONING AND TRACKING POWER SOURCE OUTLET BEFORE REMOV- ING OR INSTALLING ABRASIVE BELT. \ RIGHT BELT LOCKING SCREW LEFT BELT MOVING TO RIGHT DRIVE PULLEY / \ / "rge ng to know you belt and disc sander 4. BACKSTOP LOCK SCREW locks the backstop in 5. BELT TABLE LOCKING BOLTS ... lock the belttable in position. 6, ABRASIVE BELT TABLE STOP basic operation AVOID ACCIDENTAL STARTING. Make sure switch is " OFF" before plugging sander into a power outlet. " rt operaho SURFACE FINISHING ON THE ABRASIVE BELT. / Page maintenance MOTOR MAINTENANCE AND LUBRICATION lubrication SEARS RECOMMENDS THE FOLLOWING ACCESSORIES i i _'i " i i_ ,ii i_i_ trouble shooting POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING YOUR SANDER, TROUBLE SHOOTING CHART TROUBLE SHOOTING -- MOTOR repair parts CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.2259OO & 113.225931 FIGURE 1 PARTS LIST SUPPLIED WITH MODEL 113.225931 ONLY CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.225900 & 113,225931 -:> Q "ql CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.225900 & 113,225931 FIGURE 2 PARTS LIST 32 repair parts CRAFTSMAN BELT AND DISC SANDER MODEL 113.225931 2B \ FIGURE 3 -MOTOR PART NO. 68072 SUPPLIED WITH MODEL 113.225931 ONLY Page repair parts CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.225900 &113.225931 _ _i _ 6 S 34 FIGURE 4 PARTS LIST ON\OFF POWER OUTLET 60382 AND MOUNTING BRACKET Page SERVICE MODEL NO. 113.225900 MODEL NO. 33 3.225931 HOW TO ORDER REPAIR PARTS BEL T AND DISC SANDER Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.